16
AUTOMATIC RUNNING
Activation
1)
Depress the pushbutton with the bottom running symbol
for a short period..
a) Whirlpool running through nozzles with flow from the water supply mains controlled with a tap will be started.
b) Running time will be displayed on the display and counted down by 1 second till automatically turning off.
c) Water level will be stopped above the massage nozzles.
d) Safety time interval protecting against flooding is fixed for whirlpool running (maximum 10 minutes).
e) To raise water level or to refill water, it is necessary to use tap or shower changeover switches.
Turning off
2)
By a short depression of the running pushbutton
3)
By keeping the turning on/off pushbutton
depressed.
4)
In an emergency case, by disconnecting the system from the mains
After whirlpool filling with water (either automatically or manually through the tap above the whirlpool system
nozzles), the control unit system is switched over to
LEVEL 2: the whirlpool is full
and the functions illustrated
above the controller pushbuttons are ready
HYDRO-MASSAGE
Activation
1)
Depress the Hydro pushbutton with the top symbol
depressed.
I) Activate hydro-massage for the period of 20 minutes specified beforehand.
II) Passed hydro-massage time alternated with daily time and water temperature will be displayed on the display.
b) Pump speed can be increased or reduced using the step pushb/-.
Slow oscillation
2)
Depress the Hydro pushbutton with the top symbol
for a short period again.
I) Pump speed will start oscillating in regular intervals.
Turning off
3)
Depress the Hydro pushbutton with the top symbol
for a short period again or turning off takes place au-
tomatically after time limit elapsing.
4)
Turn all active functions off by keeping the pushbutton
depressed.
I) Hydro-massage is blocked in case of low water level (LEVEL 1).
Setting
5)
Depress the hydro-massage pushbutton with the top symbol
twice for a short period while the pump is idle.
I) The period that has been set for hydro-massage will appear on the display.
II) You can (shorten -/) the massage period by means of the step pushbuttons 5 / 10 / 15 and 20 minutes.
III) The set time will always be counted down from the previous settings on the hydro-massage or aeration
system function.
IV) All units that have been activated (Lighting, Heating, Hydro, Air) are turned off after the time limit elapses.
Caution:
Do not leave the pump active in the slow oscillation function or at low speed for too long (no longer
than for 10 minutes) in order to avoid premature wear of the pump.
AIR-MASSAGE
Activation
1)
Depress the Air pushbutton with the top symbol
.
I) Activate air-massage for the period of 20 minutes specified beforehand.
II) Passed hydro-massage time alternated with daily time and water temperature will be displayed on the display.
b) Compressor speed can be increased or reduced using the step pushb/-.
Slow oscillation
2)
Depress the Air pushbutton with the top symbol
for a short period again.
I) Compressor speed will start oscillating in regular intervals.
II) Do not leave this function active too long because of potential compressor overheating.
Turning off
3)
Depress the Air pushbutton with the top symbol
for a short period again or turning off takes place automati-
cally after the time limit elapses.
4)
Turn all active functions off by keeping the pushbutton
depressed.
I) Air-massage is blocked in the case of low water levels.
Setting
5)
Depress the air-massage pushbutton with top symbol
twice for a short period while the compressor is idle.
I) The period that has been set for air-massage will appear on the display.
II) You can (shorten -/) the massage period by means of the step pushbuttons 5 / 10 / 15 and 20 minutes.
III) The set time will always be counted down from the previous settings on the hydro-massage or air-massage
system function.
IV) All units that have been activated (Lighting, Heating, Hydro, Air) are turned off after the time limit elapses.
