background image

Important Safety Instructions 

VOLTAGE INFORMATION

•   The power requirement for the Teeter Power VI Inversion Table include a grounded, dedicated circuit with a nominal voltage of 220 
    VAC at 50 Hz. Voltage requirements are also located on the serial number decal on the inversion table.

To avoid the risk of electric shock, 

ALWAYS 

connect to a supply mains with protective earth that matches the voltage 

requirements of the inversion table that has been received. 

DO NOT

 attempt to use this unit with a voltage adapter. 

DO NOT 

attempt to use this unit with an extension cord. 

DO NOT

 plug more than one unit into a single circuit. 

ALWAYS

 ensure that 

the inversion table is connected to an outlet having the same configuration as the plug. 

DO NOT

 use a ground plug adapter 

to adapt the power cord to a non-grounded outlet.

WARNING

!

GROUNDING INSTRUCTIONS

 •  The Power VI Inversion Table must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for 
    electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and      
    a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all 
    local codes and ordinances.

ALWAYS 

ensure the equipment is properly grounded to avoid risk of serious injury or death. 

ALWAYS 

check with a 

qualified electrician or service provider if there is doubt as to whether the inversion table is properly grounded. Improper 

connection of the equipment grounding conductor can result in a risk of electric shock. 

WARNING

!

2

CHOOSING & PREPARING A SITE

• Before assembling the inversion table, a suitable site must be selected and have the proper electrical outlet power available for 
optimum  
  operation and safety. See the 

Voltage Information 

section on this page to determine the inversion table's voltage requirements. Note 

the 
  Technical Description on pg. 6 for optimum performance.  

• The area selected for the inversion table should be well lit and well ventilated. Locate the inversion table on a structurally sound and level 
  surface with ample clearance from walls and other equipment. Users will require adequate space to rotate the table. In front of the  
  inversion table should have a 43 in (109.2 cm) minimum space. Behind the inversion table should be 33 in (83.8 cm) minimum of space. 
  Allow enough clearance for safe access and passage during use of the machine.  

• Do not install the inversion table in an area of high humidity, such as in the vicinity of a steam room, sauna, indoor pool, or outdoors. 
  Exposure to extensive water vapor, chlorine, and/or bromine could adversely affect the performance of the machine. 

• If possible, set up the product at or near the space in which you intend to use it to avoid moving it later.  

PRODUCT MAINTENANCE & CLEANING

•  Facilities are responsible for the cleaning and maintenance of the equipment. All maintenance activities shall be performed by qualified 

personnel. 

•  Regularly wipe down the unit with mild soap and water. DO NOT use abrasive cleaners or solvents. 
•  Schedule routine equipment inspections to verify that the unit is clean and functions properly, all parts rotate smoothly, and all fasteners 

To avoid the risk of serious injury or death,

 

 

ALWAYS 

ensure that all controls are turned to the OFF position and remove the plug from 

the outlet immediately after using and before cleaning or servicing.

WARNING

!

Summary of Contents for Power VI-GL

















Reviews: