background image

Page 8

Four-Cycle • Vertical Crankshaft • Air-Cooled

181-1132-14

B. Engines with Recoil Starters

Only one of the following two sections will apply to your 
engine. See Table 4.

I. Combined Speed and Choke Control

1. To avoid carbon monoxide poisoning, ensure engine is 

outdoors in a well-ventilated area.

2. Move combined control to “CHOKE” or “START” posi-

tion if present (see equipment manufacturer’s instruc-
tions). See Figures 12 and 13.

 NOTE

If restarting a warm engine after a short shutdown, move 
combined Control to “FAST” instead of “CHOKE” or 
“START” position. See Figures 12 and 13.

When pulling starter rope, the rope 
can unexpectedly jerk back toward 

engine causing serious injury. To avoid this risk, carefully 
follow these instructions:
3. Grasp starter cord handle. See Figure 14.

a. Pull rope out slowly until you feel drag.
b. Without allowing the rope to retract, continue   

pulling rope with one rapid full arm stroke.

c. Return rope 

slowly

 to original position.

 NOTE

Following the instructions listed in the steps above avoids 
potential damage to the recoil mechanism.

If engine fails after 3 pulls repeat steps 2 thru 3.

4. When engine starts:

d. Move combined

 

control to “FAST” position.

e. Next, move combined

 

control to desired speed in 

“RUN” range. See Figure 12.  See Figure 13. 

 NOTES

If engine starts, but falters when combined control is moved 
to “FAST” position:

a. Momentarily move combined control back to 

“CHOKE” position.

b. Next, move combined control to “FAST” position.
c. Finally, move combined control to desired speed in 

“RUN” range.

If engine dies after combined control is moved to “FAST” 
position, repeat steps 2 thru 4 to restart engine.

5. If engine fires but does not continue to run, move com-

bined control lever to “FAST” position and pull the 
starter rope.

6. If engine fails to start after 3 attempts with combined 

control in the “FAST” position, move combined

 

control 

to “FULL CHOKE” position and pull the starter rope 
again.

7. If engine does not start after following steps 1 thru 6, 

contact your Authorized Tecumseh Servicing Dealer. 
DO NOT attempt to start or troubleshoot this engine in 
any other way.

Table 4. Engine Sections with Recoil Starters

If your engine has:

Go to:

Combined Speed and Choke Controls Section B.I

Independent Speed and Choke 
Controls

Section B.II

!

WARNING

Figure 12. Combined Speed and Choke Control

Figure 13. Typical Engine Symbols

Figure 14. Recoil Starter

STOP

STOP

SLOW

RUN

FAST CHOKE

Summary of Contents for OHV 135





















Reviews: