TECPEL OS-81B Manual Download | Manualshive

Page: 19 / 54

background image

18

Y-axis adjustment: Press

Range

button under scope

mode, the corresponding functional button:

Move

Move

Rang

Rang

F1

F2 F3 F4

F1:

move up the waveform

F2:

move down the waveform

F3:

go up range

F4:

go down a range

The auto set feature will be off when changing the
measurement mode

Press

Time

button under scope mode, the

corresponding functional button:

Base

Base

Base <

Base >

F1 F2 F3 F4

F1:

increase the number of periods

F2:

decrease the number of periods.

F3:

trigger point move left

F4:

trigger point right move

The auto set feature will be off when changing the

measurement mode.

OS-81B

Oscilloscope multimeter

«
...
17
18
19
20
21
...
»

Summary of Contents for OS-81B























































Reviews:

No comments

Related manuals for OS-81B

Brand: Paradyne Pages: 19

Brand: Victor Pages: 2

Brand: Iso-Tech Pages: 4

Brand: Iso-Tech Pages: 32

Brand: Di-LOG Pages: 36

Brand: Perel Pages: 50

Lilliput HDS2062M-N

Brand: Owon Pages: 74

Brand: Tenma Pages: 8

Brand: Amprobe Pages: 55

Brand: UNI-T Pages: 42

Brand: Mastech Pages: 11

Brand: SW Stahl PROFI Tools Pages: 8

Brand: Hameg Pages: 19

Brand: Jaycar Pages: 10

Brand: Multimetrix Pages: 92

Brand: Elmo Pages: 2

Brand: Keithley Pages: 139

Brand: Kaise Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands