2
rev. RPA-v2_0_en
Table 2
- Function of plugs
Plug
Function
Jumper
Note
F1
Firmware update
before power on
F2
Set operation
mode
standby mode
(with
power on)
service mode
the jumper is installed on two pins of the plug; jumper
removed (or installed for storage on one pin of the plug)
NOTE! When registering and in standby mode, the jumper from
the F1 plug must be removed.
5 Indication
Table 3
- POWER indicator notifications and Control Panel.
Status
Power LED
Control
Panel
Power-on test
1 time flash yellow then green
-
Standby mode
(Power is normal)
Solid green
-
Main power failure
x1 yellow flashes every 3 sec.
+
Backup power
failure
x1 flash per 1 time every 3 sec
+
Power failure
Solid yellow
+
RPA firmware up-
date
Not on
-
«+» - the notification is sent to the Control Panel
«-» - the notification is not sent to the Control Panel
__________________________________________
__________________________
* a notification is issued in the event of a FAILURE or voltage drop
below 10 V simultaneously on both power inputs
Table 4
–FAILURE indicator and Control Panel notifications
Status
Failure LED
Control
Panel
Power-on test
one time yellow flash
-
Any
failure
(tampering,
SLC failure, power input
failure)
Solid yellow
+
No failures
Off
-
Firmware update
Solid yellow
-
«-» - the notification is not sent to the Control Panel,
«+» - the notification is sent to the Control Panel
Table 5
- Notifications on the INTERFACE indicator and Control Panel in
the service mode
Status
Interface LED
Control
Panel
RPA is registered to the Control Panel
Connection with Control
Panel is normal. No activity
with Control Panel on D1
and D2
x3 yellow
flashes
per 1 time every 3 sec.
-
Connection with Control
Panel is normal. No activity
with Control Panel via D1.
x1 yellow
flash
every 3
sec.
-
Connection with Control
Panel is normal. No activity
with Control Panel via D2.
x2 yellow
flashes
every 3
sec.
-
Connection with Control
Panel is normal. Activity with
Control Panel via D1 and
D2.
Solid
green
-
Status
Interface LED
Control
Panel
No connection with Control
Panel. No activity with Con-
trol Panel via D1 and D2.
Solid
yellow
-
No connection with Control
Panel. No activity with Con-
trol Panel via D1.
x1 yellow
flash every
1 sec
.
-
No connection with Control
Panel. No activity with Con-
trol Panel via D2
x5 yellow
flashes every
1
sec.
-
No connection with Control
Panel. Activity with Control
Panel via D1 and D2
x1
green
flash every
1 sec
.
-
RPA is not in the system
Activity with Control Panel
via D1 and D2.
Not on
-
No activity with Control
Panel via D1 and D2.
x3 green
flashes
every 3
sec.
-
No activity with Control
Panel via D1
x1 green
flash
every 3 sec.
-
No activity with Control
Panel via D2
x2 green
flashes
every 3
sec.
-
«+» - the notification is sent to the Control Panel,
«-» - the notification is not sent to the Control Panel
D1
- incoming interface RS485 Control Panel,
D2
- outcoming interface RS485 Control Panel,
Table 6
- Notifications to the
INTERFACE
LED and Control Panel
in
standby mode
Status
INTERFACE LED
Control
Panel
Power-on test
x1 yellow
flash
, then green
flash
-
RPA is not in the sys-
tem. No connection with
Control Panel.
x1 green
flash
every sec.
-
RPA is in the system.
Connection with Control
Panel is fine.
Solid
green
+
RPA is not in the system
Off
-
Firmware update
Off
-
«-» - the notification is not sent to the Control Panel
«+» - the notification is not sent to the Control Panel
Table 7
– SLC LED and Control Panel NOTIFICATIONS
Status
SLC LED
Control
Panel
Power-on test
x1yellow flash then green
flash
-
Stand By mode
Solid green
+
Line open
CRC
addressable
device
x1
yellow
flash every
1 sec.
+
No addressable
device
x1
green
flash every
1 sec.
Ring/bea
m
addressable
device
Solid
green
no addressable
device
Off
Addressable device regis-
tration
x1 green/yellow
alternating
every
1 sec.
-
Registration failure
x5 yellow
flashes per
1 sec
during
5 sec.
SLC1 Power failure
x1 green
flash
every 3 sec.
+
