background image

 

  1

7

  SUGGESTIONS FOR A CORRECT USE 

MAINTENANCE 

EVO needs minimal maintenance throughout its lifetime. 

 

WARNING 
Prior to achieve any check up or cleaning  operations  make  sure  that  the  UPS  is 

switched off and that the mains voltage in the UPS input is switched off.   

 
We advise to periodically check the mains input cable, the output connections and to dust the 

ventilation holes. 
Do not use liquids or detergents to clean the UPS. Only use a humid cloth.  
Before switching the EVO on make sure that it is perfectly dry. 
If accidentally some liquid penetrates inside the UPS, do not switch the UPS on and immediately 

consult authorised Technical Service. 

BATTERY MAINTENANCE 

The battery recharge is automatic when the UPS is ON and working in LINE mode. The 

batteries are also recharged if the UPS is OFF and connected to the mains. 
It is necessary to carry out a three-monthly functioning test in BATTERY mode, this will 

preserve the batteries in an excellent state and extend the life duration. 
Leave the UPS in BATTERY mode until the end of autonomy condition is reached. After which 

restore the input mains. The UPS will return functioning in LINE mode and will fully recharge the 

batteries in around 8 hours. 
If the UPS is left unused, and disconnected from the mains, it is advised to recharge the 

batteries at least once in a month for around 8 hours.   
After a period of inactivity, we advise to carry out the INITIAL START UP procedure described in 

this manual, before using the UPS.    
Carefully follow the rules related to the battery maintenance. Otherwise warranty can 

be declined. 

SAFETY FOR THE OPERATOR  

 

If the EVO does not have the original security characteristics, it must be made non functional, 

and a non authorised use must be avoided. 
The problem must then be reported to qualified technical personnel. 
The original security characteristics can be lost if for example the EVO shows visible damages or 

an anomalous running. 

User’s manual 

15 UPS 

EVO

 

Summary of Contents for EVO 1.0

























Reviews: