background image

 
The UPS warns the user of this LOW BATTERY condition by increasing the acoustic alarm signal 

(there is an acoustic signal every second) and by turning on the yellow led of the BAT. LEVEL.  
If the AC utility power is not restored within one minute of this condition, the UPS will 

automatically switch OFF. This will protect the batteries from a sudden discharge. EVO RT 

will stop supplying output power, will deactivate the alarm signals and will place itself in a 

stand-by mode.  When the AC utility power is restored, the UPS automatically switches ON 

and returns to work in LINE mode.   
After a complete discharge the UPS will need around 8 hours to completely recharge the 

batteries.  The recharge is automatic in either two ways: 

 

The UPS is ON and running in LINE MODE  

 

The UPS is OFF and connected to an AC input line 

LOAD TEST 

EVO RT indicates the output power percentage through the LOAD LEVEL bar. The output power 

is proportional to the number of leds switched on as described in the chapter “External 

description”.  
The UPS warns of an OVERLOAD condition by lighting up the red OVERLOAD led at the top of 

the LOAD LEVEL bar. 
In LINE mode, EVO RT has the capability to accept an overload from 110% to 150% for about 

30 seconds (the UPS indicated the OVERLOAD condition by lighting up the red OVERLOAD led 

and by an acoustic signal every second) and after it switches automatically to the BYPASS 

MODE. 
In LINE mode, EVO RT automatically switches to BYPASS mode as soon as the overload is 

higher than 150%. 
Once the requested power is back within range, EVO RT automatically switches to LINE mode 

again. 
In BATTERY mode, EVO RT has the capability to accept an overload from 110% to 150% for 

around 30 seconds (the UPS indicates the OVERLOAD condition by lighting up the red 

OVERLOAD led and by an acoustic signal every second) after which it turns OFF automatically.  
In  BATTERY  mode,  EVO  RT  switches  automatically  off  as  soon  as  the  overload  is  higher  than 

150%. 
After removing the cause for the overload condition in order to switch the UPS ON again it is 

necessary to press the OFF button.  Wait for a few seconds and then press the ON/TEST/ALARM 

button. 

It is possible to carry out a LOAD TEST in the following way:  

 

Make sure that UPS is working in LINE mode, with all powered equipment switched ON and 

absorbing MAXIMUM POWER.

   

 

Press the 

ON/TEST/ALARM button

 for more than 1 second, to start the TEST. 

EVO RT begins operating in BATTERY mode. The TEST is overcome if all equipments keep on 

working and if the UPS does not signal any anomalies (overload or other).  After a few seconds 

the TEST is finished and the UPS returns in LINE mode. 

We advise you to carry out the LOAD TEST periodically in order to check the UPS  

efficiency.   

WARNING 
Make sure that the UPS never indicates OVERLOAD when running. 
Do not connect a load greater than the rated nominal value on the UPS label (see 

POWER specifications in the TECHNICAL CHARACTERISTICS chapter), as this may 

damage the unit. In this case the warranty is void. 

User’s manual 

11 

UPS EVO RT

 

Summary of Contents for EVO 1.0 RT

























Reviews: