Tecnologic TLV 38, Operating Instructions Manual

Page: 6 / 8

3) verify that the instrument or the device are supplied
4) observe the indication led on the device KEY 01: it has to result
green, because if the led results green blinking or red blinking, this
means that on the device it has not been downloaded any valid
configuration and therefore it’s useless to continue.
5) if the les results green, press the button placed on the device.
6) observe the indication led : after having pressed the button, the
led becomes red and therefore, at the end of the data transfer, it
becomes green.
7) now it is possible to disconnect the device.
Instrument supplied and device not supplied
SUPPLY
Instrument supplied from the device
SUPPLY ADAPTER
12 VDC AC SUPPLY
For additional info, please have a look at the KEY01 instruction
manual.
5 - PROGRAMMABLE PARAMETERS
Here following are described all the parameters available on the
instrument. Some of them could be not present or because they are
depending on the type of instrument or because they are
automatically disabled as unnecessary.
Group “
]
InP” (parameters relative to the measure input)
0 SSC ÷ FSC Zero value with V / I
signals
0.Pot
4
100 SSC ÷ 9999 High scale limit input
with V / I signals
FSC 3
0 -1999 ÷ FSC Low scale limit input
with V / I signals
SSC
2
J
Ptc
4.20
0.10
input C :
J / CrAL / S /
Ir.J / Ir.CA /
Pt1 / 0.50 /
0.60 / 12.60
input E :
J / CrAL / S /
Ir.J / Ir.CA /
Ptc / ntc /
0.50 / 0.60 /
12.60
input I :
0.20 / 4.20
input V :
0.1 /
0.5 / 1.5 /
0.10 / 2.10
Probe type:
J= thermocoupled J
CrAL= termocoupled K
S= thermocoupled S
Ir.J=Infrared Sen. IRS J
Ir.CA= Infrared Sen.
IRS K
Pt1= thermores. Pt100
0.50= 0..50 mV
0.60= 0..60 mV
12.60= 12..60 mV
Ptc= thermistor PTC
KTY81-121
ntc= thermistor NTC
103-AT2
0.20= 0..20 mA
4.20= 4..20 mA
0.1= 0..1 V
0.5=0..5 V
1.5= 1..5 V
0.10= 0..10 V
2.10= 2..10 V
SEnS 1
Note Def. Range Description Par.
1.000 0.000 ÷ 2.000 Rotation of the
measuring straight line
rot 9
0 -1999 ÷ 9999 Measuring Offset OFSt 8
1.0 0FF÷ 20.0
sec.
Input digital filter
FiL
7
°C °C / °F Temperature unit of
measurement
Unit 6
0 Pt1 / Ptc / ntc:
0 / 1
norm sig.:
0 ÷ 3
Number of decimal
figures
dP 5
Group“
]
Out” (parameters relative to the outputs)
ALno ALno / ALnc
ALni / OFF
Functioning of output 2:
see “O1F”
O2F
11
ALno ALno / ALnc
ALni / OFF
Functioning of output 1:
ALno= Alarm Out nor-
mally opened
ALnc= Alarm Out nor-
mally closed
ALni= Alarm Out nor-
mally closed with rever-
se led func.
O1F
10
Note Def. Range Description Par.
Group “ ] AL1” (parameters relative to alarm AL1)
no no / yES Alarm AL1 activation in
case of measuring error
AL1i
20
OFF OFF ÷ 9999
sec.
Activation delay of
alarm AL1 AL1d 19
1 OFF ÷ 9999 Alarm AL1 hysteresis HAL1 18
9999 AL1L ÷ 9999 High threshold band
alarm AL1 or Maximum
set alarm AL1 for high
or low alarm
AL1H
17
-1999 -1999 ÷ AL1H Low threshold band
alarm AL1 or Minimum
set alarm AL1 for high
or low alarm
AL1L
16
0 AL1L÷ AL1H Alarm AL1 threshold
AL1
15
0 0 ÷ 15 Alarm AL1 functioning:
+1 = not activated at
power on
+2 = delayed
+4 = latch
+8 = aknowledged
Ab1
14
LoAb LoAb / HiAb
LHAb
Alarm AL1 type:
LoAb= Low
HiAb= High
LHAb= Band
AL1t 13
Out1 Out1 / Out2 /
OFF
Output where alarm
AL1 is addressed
OAL1
12
Note Def. Range Description Par.
Gruppo “ ] AL2” (parametri relativi all’allarme AL2)
OFF OFF ÷ 9999
sec.
Activation delay of
alarm AL2
AL2d
28
1 OFF ÷ 9999 Alarm AL2 hysteresis
HAL2
27
9999 AL2L ÷ 9999 High threshold band
alarm AL2 or Maximum
set alarm AL2 for high
or low alarm
AL2H
26
-1999 -1999 ÷ AL2H Low threshold band
alarm AL2 or Minimum
set alarm AL2 for high
or low alarm
AL2L 25
0 AL2L÷ AL2H Alarm AL2 threshold AL2 24
0 0 ÷ 15 Alarm AL2 functioning:
see “AL1”
Ab2 23
LoAb LoAb / HiAb
LHAb
Alarm AL2 type:
see “AL1” AL2t 22
Out2 Out1 / Out2 /
OFF
Output where alarm
AL2 is addressed
OAL2
21
Note Def. Range Description Par.
TECNOLOGIC spa - TLV 38 - OPERATING INSTRUCTIONS - Vr. 01 - ISTR 06612 - PAG. 6