Tecnologic TLV 38 Operating Instructions Manual Download Page 1

    

TLV 38

MICROPROCESSOR-BASED

DIGITAL ELECTRONIC

INDICATOR

OPERATING INSTRUCTIONS

Vr. 01 (ENG) - cod.: ISTR 06612

TECNOLOGIC S.p.A.

VIA INDIPENDENZA 56

27029 VIGEVANO (PV) ITALY

TEL.:  +39 0381 69871

FAX: +39 0381 698730

internet : http:\\www.tecnologic.it

e-mail: [email protected]

FOREWORD

This manual contains the information necessary for the product to

be installed correctly and also instructions for its maintenance and
use; we therefore recommend that the utmost attention is paid to

the following instructions. 
Though this manual has been issued with the greatest care,

TECNOLOGIC S.p.A. will not take any responsibility deriving from
its use. 

The same applies to each person or Company involved in the
issuing of this manual. 

This document is the exclusive property of TECNOLOGIC S.p.A.
which forbids any reproduction and divulgation , even in part, of the

document, unless expressly authorized. 
TECNOLOGIC S.p.A. reserves the right to make any formal or

functional changes at any moment and without  any notice.

INDEX

INSTRUMENT ORDERING CODE

7.6

MEASUREMENT RANGE TABLE

7.5

FUNCTIONAL DATA

7.4

MECHANICAL DIMENSIONS, PANEL CUT-OUT AND

MOUNTING

7.3

MECHANICAL DATA

7.2

ELECTRICAL DATA

7.1

TECHNICAL DATA

7

GUARANTEE AND REPAIRS

6.3

CLEANING

6.2

ERROR SIGNALLING

6.1

PROBLEMS , MAINTENANCE AND GUARANTEE

6

PROGRAMMABLE PARAMETERS TABLE

5

PARAMETERS CONFIGURATION BY KEY01

4.5

FUNCTION OF KEY “U”

4.4

ALARMS OUTPUTS FUNCTIONS

4.3

PEAK VALUES MEMORIZATION AND HOLD FUNCTION

4.2

MEASURING AND VISUALIZATION

4.1

FUNCTIONS

4

ELECTRICAL WIRING DIAGRAM

3.4

ELECTRICAL CONNECTIONS

3.3

MECHANICAL MOUNTING

3.2

PERMITTED USE

3.1

INFORMATION ON INSTALLATION AND USE 

3

FAST PROGRAMMING OF ALARM THRESHOLDS

2.3

PARAMETER PROGRAMMING LEVELS

2.2

PARAMETER PROGRAMMING 

2.1

PROGRAMMING

2

FRONT PANEL DESCRIPTION

1.2

GENERAL DESCRIPTION

1.1

INSTRUMENT DESCRIPTION

1

1 - INSTRUMENT DESCRIPTION

1.1 - GENERAL DESCRIPTION

TLV 38  is a digital microprocessor-based indicator.
Depending on the model required the input accept:

C

: Thermocouples temperature probes (J,K,S and TECNOLOGIC

IRS Infrared sensors), mV signals (0..50/60 mV, 12..60 mV),
Thermoresistances PT100.

E

 : Thermocouples temperature probes (J,K,S and TECNOLOGIC

IRS Infrared sensors), mV signals (0..50/60 mV, 12..60 mV),
Thermistors PTC and NTC.

I

 : normalized analogue signals 0/4..20 mA

V

 : normalized analogue signals 0..1 V, 0/1..5 V, 0/2..10 V

The instrument can have up to 2 outputs: relay type or can drive
solid state relays type (SSR).

The process value is visualized on 4 red displays, while the output
status is indicated by 2 LED displays.

Other important available functions are: 
maximum end minimum peak memory, Hold function, zero

calibration (resetting) function and/or auto-ranging for normalized
signals, parameters protection on different levels.

1.2 - FRONT PANEL DESCRIPTION

OUT1

TLV 38

1

7

2

3

4

5

6

OUT2

1 - Key P

 : This is used to access the programming parameters

and to confirm selection.

2 - Key DOWN

 : This is used to decrease the values to be set and

to select the parameters. If the key is held down, the user returns to
the previous programming level until he exits the programming

mode. Outside the programming mode it permits visualisation of
the minimum peak measure.

TECNOLOGIC spa - TLV 38

 

- OPERATING INSTRUCTIONS - Vr. 01 - ISTR 06612 - PAG. 1

Summary of Contents for TLV 38









Reviews: