background image

 

Electric Oven rev.0

________________________________________________________ 

EKF 2011 UD – EKF 1664 UD 

_________________________________________________________________________________________ pag 21 

12. Technical service 

 
Before  leaving  the  factory,  the  appliance  was  completely  regulated  and  tested  by  expert 
specialised personnel to guarantee the best operating results. 
All repairs and settings must be performed with utmost care and attention, respecting national 
safety  regulations  in  force.  Always  contact  your  retailer  or  our  nearest  Service  Centre,  giving 
details of the problem, the appliance model and the serial number (on the rating plate on the 
rear panel).  
For  servicing  needs  the  user  may  contact  Tecnoeka  on  the  numbers  shown  on  the  cover,  or 
refer to the website www.tecnoeka.com. 

 

13. Informations to the consumers

 

 
Further  to  Directive  2012/19/UE,  the  symbol  of  the  crossed  rubbish  skip  on 
the appliance means that at the end of its life, the product must be disposed 
of separately from the other rubbish. The user must hand the appliance to a 
specialised waste collection centre for electric and electronic equipment. 

 

The separate collection of the rubbish and subsequent treatment, recovery and disposal help to 
produce  other  equipment  using  recycled  materials,  reducing  the  negative  effects  on  the 
environment  and  public  health,  which  would  be  caused  by  incorrect  management  of  the 
rubbish.  Should  the  user  dispose  of the  product abusively,  administrative  sanctions  would be 
applied

.

 

Summary of Contents for EKF 1664 UD

























Reviews: