background image

TFNET

17

 

TECNO OUT

DDNS

TFNET                121016

*2903000024*

*2903000024*

RJ45

7 - ELECTRONIC BOARD

RS485 BUS

RS485 MODBUS BUS

1

+

Supply positive

5

NC

Not connected (terminal not used)

2

-

Supply negative

6

-

Reference negative of RS485 BUS output

3

A

Communication channel A  

7

A

Communication channel A  

4

B

Communication channel B

8

B

Communication channel B

Ethernet RJ45 connector

Identifi cation

Colour

Function

1

White / Green

5

White / Blue

RUN LED

Green

LED monitoring the functional state of the device. 
Flashing: normal operation state

2

Green

6

Orange

3

White / orange

7

White / Brown

LINE LED

Red

LED signalling that the device is using the Ethernet line

4

Blue

8

Brown

Jumper JP6 - Termination of RS485 serial line

Open

With the jumper open, the Bus is not terminated. Open the jumper when the device is not the last device connected 
on the Bus. Condition valid for both wiring con

fi

 gurations of the line Bus: open or closed  

Closed

With the jumper closed, the Bus is terminated. Close the jumper when the device is the last device connected on the 
Bus. Of course only if the connection Bus is in open line con

fi

 guration.

Identifi cation

Normal condition

Function

JP1 - RESET

   Open

Hardware reset

JP2 - BOOT

   Open

Used to update the 

fi

 rmware of the product (RJ45 port Ethernet connection)

JP3 - DEFAULT

   Open

No function (reserved for future developments)

SW1 Serial address setup

Address

Dip 1

Dip 2

Dip 3

Dip 4

Dip 5

Dip 6

Address

Dip 1

Dip 2

Dip 3

Dip 4

Dip 5

Dip 6

0

OFF

OFF

OFF

OFF

OFF

OFF

9

ON

OFF

OFF

ON

OFF

OFF

1

ON

OFF

OFF

OFF

OFF

OFF

10

OFF

ON

OFF

ON

OFF

OFF

2

OFF

ON

OFF

OFF

OFF

OFF

11

ON

ON

OFF

ON

OFF

OFF

3

ON

ON

OFF

OFF

OFF

OFF

12

OFF

OFF

ON

ON

OFF

OFF

4

OFF

OFF

ON

OFF

OFF

OFF

13

ON

OFF

ON

ON

OFF

OFF

5

ON

OFF

ON

OFF

OFF

OFF

14

OFF

ON

ON

ON

OFF

OFF

6

OFF

ON

ON

OFF

OFF

OFF

15

ON

ON

ON

ON

OFF

OFF

7

ON

ON

ON

OFF

OFF

OFF

16

OFF

OFF

OFF

OFF

ON

OFF

8

OFF

OFF

OFF

ON

OFF

OFF

Notes:

 setting address 0 disables the operation of the communicator. Accepted addresses range from 1 to 16.

All other logic combinations are reserved.

Identifi cation

MODBUS BUS balance

JP4

MODBUS 

BALANCE

  Open

RS485 MODBUS line not terminated

  Closed

RS485 MODBUS line terminated

JP5

  Open

  Closed

JP7

  Open

  Closed

Summary of Contents for TecnoFire TFNET

























Reviews: