background image

16

WARRANTY

Tecnimed s.r.l. guarantees this product against any lack of conformity for 24 

months as of the date of purchase (indicated on the cash register receipt or other 

fiscal document). Follow the instructions given by your Dealer for the technical 

service procedures. 

This warranty does not cover the batteries and any damage caused by defective 

or run down batteries or damage to the casing due to carelessness or improper 

use. The warranty is also voided if:

- the product is tampered with, damaged or used improperly;

- the label on the back bearing the serial number is removed, damaged or rende-

red illegible;

- the product is opened or repaired by unauthorized personnel; 

- the product has been damaged due to non-compliance with the instructions 

given in this manual.

If Technical Service is required, contact the Manufacturer or your Dealer. 

In case the Product was purchased through an Online-store, warranty service 

can only be provided through the Internet Seller, where the product was pur-

chased. In case of any lack of conformity, the product will be either repaired or 

replaced, as decided by the Manufacturer or Dealer, at their sole discretion. Any 

repaired or replaced product does not extend the original warranty beyond the 

period of 2 years from original date of purchase.

If, after technical evaluation, the Product is found not to be covered by the terms 

and conditions of this Warranty (because no lack of conformity is found), Tecni-

med reserves the right to charge a handling fee for technical check and delivery.

Under no circumstance may Tecnimed be held responsible for damages related 

to the improper use of the product or for costs exceeding the original price of the 

product.

Summary of Contents for Visiofocus Smart 06470



















Reviews: