background image

BRAND 

Sotech International 

Commercial Registration Number/N°SIRET: 4250992000016 

33 Avenue du Maréchal de Lattre de Tassigny 

94120 Fontenay sous Bois - France

 

REFERENCE 

MODEL IDENTIFIER 

TMAC-1091 - TMAC-1096 

Tension d’Entrée 

Input Voltage 

100-240 

Fréquence du CA d’entrée 

Input AC frequency 

50/60 

Hz 

Tension de sortie 

Output voltage 

6,0 

Courant de sortie 

Output current 

1,5 

Puissance de sortie 

Output power 

9,0 

Rendement moyen en mode actif 

Average active efficiency 

82,8 

Rendement à faible charge (10%) 

Efficiency at low load (10%) 

76,3 

Consommation électrique hors charge 

No-load power consumption 

0,07 

 

The characteristics can change without prior notice. 

 
 
This device complies with EC directives, it was controlled according to all current 
European directives, applicable such as: electromagnetic compatibility (EMC) and 
low voltage (LVD).  
This device has been designed and manufactured in compliance with the latest 
regulations and technical requirements for safety. 
 
Always unplug the appliance before any cleaning or maintenance 
operation and accessories assembly. 
 
CAUTION: In order to minimize the risks of electric shock, In the event of 
breakdown, not to open the case but to call upon a qualified technician 
for repairs. 
 
 

Imported by Sotech International  

" LE PERIPOLE " N°A-107 

33, Avenue du Marechal de Lattre de Tassigny 

94120 Fontenay sous-bois - France 

 

20 

 

Summary of Contents for TMAC-1091





















Reviews: