Techroutes S3740F Hardware Installation Manual Download Page 18 | Manualshive

Page: 18 / 22

Techroutes S3740F Hardware Installation Manual Download Page 18

S3740F Hardware Installation Manual

- 14 -

1

Sending/receiving the normal phase of data 0 TP0+

2

Sending/receiving the paraphase of the data 0 TP0-

3

Sending/receiving the normal phase of data 1 TP1+

4

Sending/receiving the normal phase of data 2 TP2+

5

Sending/receiving the paraphase of the data 2 TP2-

6

Sending/receiving the paraphase of the data 1 TP1-

7

Sending/receiving the normal phase of data 3 TP3+

8

Sending/receiving the paraphase of the data 3 TP3-

3.3.4 Connecting Gigabit Ethernet SFP ports

The S3740F switch has 24 Gigabit SFP ports. To use the optical port, you need connect

it to the SFP optical module, and then to other Ethernet terminal devices through an optical
fiber.

Figure 3-9 Connecting the 1000 SFP port and other Ethernet terminals

3.4 Checking After Installation

Before electrically starting up the switch, perform the following checkups after the switch is

installed:



If the switch is installed on the cabinet, check whether the installation point between the

cabinet and the switch is strong. If the switch is installed on the desk, check whether

«
...
16
17
18
19
20
...
»

Summary of Contents for S3740F























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands