background image

28

Warranty conditions

Note: 

The following warranty conditions do not in any way limit the legal right to warranty, but rather expand

your rights as a consumer.

1. The company Technische Alternative RT GmbH provides a one-year warranty from the date of purchase

for all the devices and parts which it sells. Defects must be reported immediately upon detection and

within the guarantee period. Technical support knows the correct solution for nearly all problems. In this

respect, contacting us immediately will help to avoid unnecessary expense or effort in troubleshooting.

2. The warranty includes the free of charge repair (but not the cost of on site troubleshooting, removal,

refitting and shipping) of operational and material defects which impair operation. In the event that a

repair is not, for reasons of cost, worthwhile according to the assessment of the Technische Alternative

company, the goods will be replaced.

3. Not  included  is  damage  resulting  from  the  effects  of  over-voltage  or  abnormal  ambient  conditions.

Likewise, no warranty liability can be accepted if the device defect is due to: transport damage for which

we are not responsible, incorrect installation and assembly, incorrect use, disregard of operating and

installation instructions or incorrect maintenance.

4. The warranty claim will expire, if repairs or actions are carried out by persons who are not authorised to

do so or have not been so authorised by us or if our devices are operated with spare, supplementary or

accessory parts which are not considered to be original parts.

5. The defective parts must be sent to our factory with an enclosed copy of the proof of purchase and a

precise description of the defect. Processing is accelerated if an RMA number is applied for via our

home page

 

www.ta.co.at

.

 

A prior clarification of the defect with our technical support is necessary.

6. Services provided under warranty result neither in an extension of the warranty period nor in a resetting

of the warranty period. The warranty period for fitted parts ends with the warranty period of the whole

device.

7. Extended or other claims, especially those for compensation for damage other than to the device itself

are, insofar as a liability is not legally required, excluded.

Legal notice

These assembly and operating instructions are protected by copyright.

Use outside the copyright requires the consent of the company Technische Alternative RT GmbH.

This applies in particular to reproductions, translations and electronic media.

Technische Alternative RT GmbH

A-3872 Amaliendorf, Langestraße 124
Tel.: +43 (0)2862 53635

Fax +43 (0)2862 53635 7

E-Mail: 

[email protected]

--- 

www.ta.co.at

 ---

©2021

Summary of Contents for FRISTAR3-WP





























Reviews: