manualshive.com logo in svg

TechnipFMC Smith Meter AccuLoad IV, Installation & Maintenance Manual

Share
Download
TechnipFMC Smith Meter AccuLoad IV Installation & Maintenance Manual Download Page 17

AccuLoad IV Installation & Maintenance Manual

Introduction 

12

“Warning: Clean display with a damp cloth only.” This is to ensure that stray static charges are not built 

up on the surface that could lead to a static discharge.

•

Special care must be taken with shielding termination to ensure signal integrity. See 

Section 3.1: General 

Electrical Installation Requirements

 for more information.

•

The AC and DC wiring should be physically separated (do not use the same conduit or entry) to avoid 

induced noise.

ATEX- and IEC-approved installations have special requirements; see 

Section 3.2: ATEX- and IECEx-

Approved Installations

 for details.

To ensure the correct operation, 

Section 3.6.7: Typical Wiring Diagrams

 for wiring diagrams.

1.2.4  RF Radiation

The AccuLoad generates, uses, and can radiate radio frequency (RF) energy and, if not installed and used 

in accordance with this manual, may cause interference to radio communications. It has not been tested to 

comply with the limits pursuant to Federal Communications Commission’s FCC Code of Federal 

Regulations, Title 47, Part 15 (CFR 47), as electronic control equipment used by an industrial complex is 

exempt from the rules.

Operation of this equipment in a residential area may cause interference, in which case the user, at their 

own expense, will be required to take whatever measures that may be necessary to correct the 

interference. The explosion-proof version of the AccuLoad has been evaluated against international 

standard IEC 61326-1: Electrical Equipment for Measurement, Control and Laboratory Use and has been 

found to comply with European Community Electromagnetic Compatibility (EMC) Directive 2014/30/EU.

1.2.5  Site-Specific Configuration

The AccuLoad is shipped from the factory in a completely initialized state and must be properly configured 

for the specific installation prior to operation. The unit will not operate due to alarm conditions until the 

configuration is completed. Using a personal computer (PC) running the AccuMate application is the best 

method to set the initial configuration, but if AccuMate is not available, all configuration parameters are 

accessible using the AccuLoad’s touch screen. See the AccuLoad IV Operator Reference Manual 

(

MN06200

) for information about parameter settings.

1.2.6  Weights and Measures Requirements

The AccuLoad is used by a global market. Requirements regarding weights and measures may vary 

depending on the region. Users are required to verify that the AccuLoad is configured and operated in a 

manner consistent with local codes and that proper notification (permit for use) or registration has been filed 

with the local authority or jurisdiction. 

Weights and measures authorities rely on either physical sealing or electronic sealing with password 

protection to secure metrological parameters for use in legal trade. See 

Section 5.2: Sealing the Enclosure

 

in this manual for information about physically sealing the AccuLoad or the AccuLoad IV Operator 

Reference Manual (

MN06200

) for instructions on setting a password.

Summary of Contents for Smith Meter AccuLoad IV









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands