Technimount System BRACKET PRO 105 Series User Manual Download

Page: 29 / 38

www.technimount.com

BP105 UG 202002-R01

Return To Table of Contents

Maintenance Guide

CLEANING THE BRACKET SYSTEM (CONTINUED)

CLEANING SOLUTIONS CONTINUED

WARNING

Some cleaning products are corrosive in nature and may cause damage to the product if used improperly.

If the products described are used to clean the equipment, the Bracket and components must be rinsed with clean

water and thoroughly dried following cleaning. Failure to properly rinse and dry the system will leave a corrosive

residue on the surface of the product, possibly causing premature corrosion of critical components.

REMOVAL OF IODINE COMPOUNDS

Use a solution of 1/4 Tablespoon of Sodium Thiosulfate in 1 pint / .5 litre of warm water to clean the stained area.

Clean as soon as possible after staining occurs. If stains are not immediately removed, allow solution to soak or stand

on the surface. Thoroughly rinse surfaces with clean water and allow to air dry before returning unit to service.

WARNING

Failure to properly clean contaminated parts or components will increase the risk of exposure to blood borne

pathogens and may cause injury to the patient or the operator.

PREVENTIVE MAINTENANCE

A preventive and regular maintenance program should be established for all Technimount equipment. Preventive

maintenance may be required more frequently based on the usage level of the product. The Bracket requires regular

preventative maintenance. Establish and follow a preventive maintenance schedule and keep records of preventive

maintenance activities (see maintenance form in this user guide).

CAUTION

Close attention should be given to safety features including, but not limited to locking mechanisms and Discs.

Improper maintenance can cause injury or damage to the product. Maintain the product as described in this user

guide.

LUBRICATION

The Bracket System has been designed to operate without the need for lubrication. If you have questions, please

contact Technical Support at

[email protected]

CAUTION

Failure to use authorized parts, lubricants, etc. could cause damage to the cot/stretcher and will void the warranty

of the product.

Summary of Contents for BRACKET PRO 105 Series







































Search results

Summary of Contents for BRACKET PRO 105 Series

Reviews:

Related manuals for BRACKET PRO 105 Series

Brands by name

Popular brands

Technimount System BRACKET PRO 105 Series, User Manual

Search results

Summary of Contents for BRACKET PRO 105 Series

Reviews:

Related manuals for BRACKET PRO 105 Series

Brands by name

Popular brands