P-10
Bluetooth Input
The Bluetooth input will allow you to connect a Bluetooth compatible device to channel 2 of the DJ2PB. First
set the Channel 2 input selector (13) to USB2/SD2/BT. Then press the mode button to set the input to
Bluetooth. Finally open your Bluetooth device and search for Bluetooth connections. Locate the DJ2PB and
pair with it.
When using the Bluetooth input, the DJ2PB controls (play/pause, stop, next track previous track) will control
the Bluetooth device.
Master Output (RCA)
Once your audio sources are connected to the inputs on the DJ2PB, connect the master outputs on the
DJ2PB to the audio inputs on the device next in the signal’s path (pre-amplifier, equalizer and amplifier).
Connecting Microphones to the DJ2PB Mixer
There is one ¼” microphone input on the rear panel of the DJ2PB. It is important to note that these inputs
are to be used solely for a microphone. Do not attempt to use these inputs for any other use. To use, simply
plug a microphone into the ¼" input while the DJ2PB and microphone is in the OFF position and the
microphone volume is turned down. Once plugged in power-on the DJ2PB, then power-on the microphone,
then slowly increase the microphone volume knob (6).
Using the Crossfader
The crossfader will allow you to mix the audio from channels 1 & 2 and play that audio through the master
output. Set the crossfader to the left to hear channel 1 only. Set the crossfader to the right to hear channel 2
only. Set the crossfader to the middle to hear both channel 1 & 2.
Using the Cue Selector
Use the cue knob to select which channel(s) will be played through the headphone output. Select the Cue for
CH1 to hear Channel 1 through the headphones (etc..). Be sure to have the headphone volume knob (21)
turned down, until you are ready to use the headphones and then slowly turn up the volume.
Connecting the DJ2PB Mixer to the PB12 Speakers
The DJ2PB mixer has RCA (Left and Right) Master Outputs.
Using the RCA to 1/8” cables connect the Right output to the AUX input on the first PB12, and then connect
the Left output to the AUX input on the second PB12.
Charging the Power Bank
Charge the power bank by connecting it to a AC outlet. A fully charged power bank can be sure to power the
DJ2PB in a location there is no power source.
Connecting Power Bank to the DJ2PB Mixer
When using the DJ2PB in a location where there is no power, connect the DJ2PB to the power bank in order
to power the mixer. Make sure the power bank is fully charged.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements: The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the eq uipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT. FCC Radiation Exposure Statement The equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65. The equipment has very low levels of RF energy that it is deemed to comply without testing of specific absorption rati o (SAR).
The Bluetooth word mark and logos are registered trademarks owned by SIG, Inc. and any use of such marks by Technical Pro is under license. Other trademarks and trade name are those of
their respective owners.
DJPACK2GO
