background image

PAGE 4

T E C A L  6 5 0 S  O P E R A T O R ’ S   M A N U A L

Introduction

Please read all the information in this booklet before using
the unit.

Warning

HIGH TEMPERATURES ARE DANGEROUS: they can cause
serious burns to operators and ignite combustible material.
Techne have taken great care in the design of these units
to protect operators from hazards, but users should pay
attention to the following points:

USE CARE AND WEAR PROTECTIVE GLOVES TO
PROTECT HANDS;

DO NOT put hot objects on or near combustible
objects;

DO NOT operate the unit close to inflammable liquids
or gases;

DO NOT place any liquid directly in your unit;

At all times USE COMMON SENSE.

Operator Safety

All users of Techne equipment must have available the
relevant literature needed to ensure their safety.
It is important that only suitably trained personnel operate
this equipment, in accordance with the instructions
contained in this manual and with general safety standards
and procedures.  If the equipment is used in a manner not
specified by Techne the protection provided by the
equipment to the user may be impaired.
All Techne units have been designed to conform to
international safety requirements and are fitted with an
overtemperature cutout.  On some models, the cutout is
adjustable and should be set to suit the application.  On
all other models the cutout is preset to protect the unit.
If a safety problem should be encountered, switch off at
the mains socket and remove the plug from the supply.

Installation

1.

All Techne units are supplied with a power cable.
This may be integral or plug-in.

2.

Before connecting the mains supply, check the voltage
against the rating plate. Connect the mains cable to
a suitable plug according to the table below.  

Note

that the unit must be earthed to ensure proper
electrical safety.

Connections

220/240V

110/120V

Live

Brown

Black

Neutral

Blue

White

Earth

Green/yellow Green

The fused plug supplied with the mains lead for use
in the UK is fitted with the following value fuse to
protect the cable:

230V UK

10 AMP

The fuse in the unit protects the unit and the operator.
Note that units marked 230V on the rating plate work
at 220V; units marked 120V work at 110V.  In both
cases, however, the heating rate will degrade by
approximately 8%.  The rating plate is on the rear of
the unit.

3.

Plug the mains cable into the socket on the rear of the
unit.

4.

Place the unit on a suitable bench or flat workspace,
or in a fume cupboard if required, ensuring that the
air inlet vents on the underside are free from
obstruction.

5.

Note that the following symbols may be next to the
indicator lamps on the front panel of the units and
have the following meanings:

: the power indicator

: the heater indicator

: the overtemperature indicator

6.

Symbols on or near the power switch of the unit have
the following meanings:

 

I

: mains switch On

O

: mains switch Off

After use

When you have finished heating samples, remember that
parts of the unit – the tubes, blocks and associated
accessories – may be very hot. Take the precautions
listed earlier.

Guarantee

The unit is guaranteed against any defect in material or
workmanship for the period specified on the enclosed
guarantee card. This period is from the date of purchase,
and within this period all defective parts will be replaced
free of charge provided that the defect is not the result
of misuse, accident or negligence. Servicing under this
guarantee should be obtained from the supplier.
Notwithstanding the description and specification(s) of
the units contained in the Operator’s Manual, Techne
hereby reserves the right to make such changes as it
sees fit to the units or to any component of the units.
This Manual has been prepared solely for the convenience
of Techne customers and nothing in this Instruction Book
shall be taken as a warranty, condition or representation
concerning the description, merchantability, fitness for
purpose or otherwise of the units or components.

User maintenance

NOTE THAT THIS EQUIPMENT SHOULD ONLY BE
DISMANTLED BY PROPERLY TRAINED PERSONNEL.
REMOVING THE SIDE, FRONT OR REAR PANELS EXPOSES
POTENTIALLY LETHAL MAINS VOLTAGES.
THERE ARE NO USER MAINTAINABLE PARTS WITHIN
THE EQUIPMENT.
In the unlikely event that you experience any problems
with your unit which cannot easily be remedied, you
should contact your supplier and return the unit if
necessary.  Please include any details of the fault
observed and remember to return the unit in its original
packing.  Techne accept no responsibility for damage to
units which are not properly packed for shipping: if in
doubt, contact your supplier.  See the Decontamination
Certificate supplied with your unit.

1. Cleaning

Before cleaning your unit ALWAYS disconnect from
the power supply and allow to cool below 50° C.
Your unit can be cleaned by wiping with a damp
soapy cloth.  Care should be exercised to prevent
water from running inside the unit.  Do not use
abrasive cleaners.

2. Fuses

Your unit is protected by one or two fuses.  These
should only be changed by suitably qualified
personnel.
If the fuses blow persistently, a serious  fault is
indicated and you may need to return the unit to your
supplier for repair.

Summary of Contents for Tecal 650S






















Reviews: