Tech Works MC-IP Series Manual Download Page 1

 

 

 

 

 

 

800-813-1080 

www.techworks-usa.com

  01/21

 

 

 
 

 
 

The MC-IP-Series is a group of audio products 
designed to provide very high audio quality over 
ethernet using Internet Protocol. Audio quality is 
consistent 

and 

predictable 

due 

to 

the 

implementation  of  Streaming  VOIP  with  our 
tried-and-true  audio  designs  and  industry 
standard interfaces. MC-IP makes intercom plug 
and play. The MC-IP provides Master to Remote 
communication 

and 

Master 

to 

Master 

Communication  up  to  32  Masters  and  512 
Remotes. 
 
Using industry standard API for integration and 
industry  standard  25-volt  speakers  for  remote 
stations,  the  MC-IP  drops  into  most  integrated 
control  systems  using  the  door  control  and 
security  system  touch  screen  for  seamless 
operator  control  of  all  security  electronic 
systems  from  a  single  touch  screen  control 
console.  
 
By using a dedicated IP network with dedicated 
switch, operator console, field device interface, 
and  Host,  the  MC-IP  maintains  quality  audio 
with  no  IT  setup.  By  plugging  the  units  in  they 
automatically 

assign 

IP 

addresses 

and 

propagate settings based on ID settings on each 
device.  This  allows  the  system  programmer  to 
program the system the way it needs to be for a 
specific  facility  without  worrying  about  the  IT 
settings  for  proper  operation.  Maintenance 
personal, without IT skills, can swap a box and 
just set the box ID. As soon as it is attached to a 
system,  the  Host  sets  the  IT  parameters  and 
downloads  the  unique  characteristic  that  unit 
was  assigned  during  the  original  system 
programming. 
 
System  Station  hardware  offers  a  call 
confirmation  light  and  privacy  alert  tone  for 
those  areas  that  require  ADA  and  Right  to 
Privacy Act compliance. 

MC-IP-Series 

 

Modular Communication 

Internet Protocol 

Audio Intercommunication 

 
Associated Equipment: 

MC-IP-ODC-
POE 
MC-IP-ODC-TS 
MC-IP-HOST 

Operator Desk Console 
w/Power Over Ethernet 
Touch Screen Console 
Network Administrator 

MC-IP-116 

16-Channel Intercom Control 
Module 

MC-IP-116-L 

16-Channel Intercom Control 
Module w/Remote Station 
Light Output 

MC-IP-SW-16 

16 port TCP/IP Switch Rack 
Mount 

MC-IP-SW-16-
POE 

16 port TCP/IP Switch  
8 w/POE, Rack Mount 

PA-402 

Paging Amplifier 

PS-2437A 

Power Supply 

VPSS-L 

Vandal-proof Speaker Station 
w/ Lighted Call Button 

 

Design Information: 

Power 

24V DC Power Supply 
(Sold Separately) 

Frequency 
Response 

150Hz 

– 10k 

 

 

BENEFITS 

Audio and Control over a Single 
Internet Protocol Connection 

Rugged Design 

High Quality Audio 

Self-contained electronics 
eliminates the need for wiring 
separate Modules together 

Designed Specifically for 
Security, Corrections and 
Industrial applications 

Industry Standard 25-Volt 
remote speakers 

 

Summary of Contents for MC-IP Series

































Reviews: