Tech Pro NVR-ELC-32-DH Series User Manual Download Page 83

Page: 83 / 158

127

Event type: There are several options for you such as disk error, no disk, disconnection,

IP conflict and etc.

Alarm output: Please select alarm activation output port (multiple choices).

Latch: Here you can set corresponding delaying time. The value ranges from 10s-300s.

System automatically delays specified seconds in turning off alarm and activated output after
external alarm cancelled.

Show message: system can pop up the message in the local screen to alert you when an

alarm occurs.

Alarm upload: System can upload the alarm signal to the network (including alarm centre)

if you enabled current function.

Send email: System can send out email to alert you when an alarm occurs.

Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm occurs.

Figure 5-87

5.7.3

Alarm

Output

Here is for you to set proper alarm output.

Please highlight icon

to select the corresponding alarm output.

After all the setups please click OK button, system goes back to the previous menu. See Figure
5-88.

Figure 5-88

5.7.4

Manual

Record

Summary of Contents for NVR-ELC-32-DH Series































































































































































Search results

Summary of Contents for NVR-ELC-32-DH Series

Reviews:

Related manuals for NVR-ELC-32-DH Series

Brands by name

Popular brands

Tech Pro NVR-ELC-32-DH Series, User Manual

Search results

Summary of Contents for NVR-ELC-32-DH Series

Reviews:

Related manuals for NVR-ELC-32-DH Series

Brands by name

Popular brands