manualshive.com logo in svg

Tech Lighting Element CMH MR16, Installation Instructions Manual

Share
Download
Tech Lighting Element CMH MR16 Installation Instructions Manual Download Page 4

4

LENS LOCK

Install the Lamp & Lens Accessories

LAMP CARTRIDGE ASSEMBLY

Pull the snoot to remove the lamp cartridge assembly.

1

4A

4B

Unscrew the snoot from the lamp cartridge.

2

SNOOT

LAMP CARTRIDGE

2

Place a maximum of three accessories (optional) into the
lamp cartridge.

3

LAMP CARTRIDGE

4D

Replace and tighten the snoot completely to the lamp
cartridge.

4

4

SNOOT

1

4C

DIFFUSER LENS

COLOR LENS

HEXCELL LOUVER

3

LAMP CARTRIDGE

4E

6

LAMP

SOCKET

5

Pull out the socket from the lamp housing.

Push the lamp pins into the large portion of the socket
slots and rotate the lamp clockwise to lock it in place
securely.

5

6

Use

Volt,

GX10 Base

MR16 Ceramic Metal Halide lamp with
models E3RLB-C20AC_, E3RLF-C20AC_,
E3SLB-C20AC_, E3SLF-C20AC_.

ONLY

20 Watt

120

Use

Volt,

GX10 Base

MR16 Ceramic Metal Halide lamp with
models E3RLB-C39AC_, E3RLF-C39AC_,
E3SLB-C39AC_, E3SLF-C39AC_.

ONLY

39 Watt

120

Summary of Contents for Element CMH MR16









Reviews:

No comments

Brands by name

Popular brands

Load more brands