MASTER SECTION EQ
The two technologically coordinated channels enable them to share the Master EQ
section. Specifically voiced for guitar, these
active
controls set the tonal balance of
the amp relative to your environment. The Trademark 60 is designed for optimal
sound quality with Low and High at 12 o’clock. If your taste differs or if you are in a
less than optimal environment, you can compensate accordingly.
In addition to Punch in Channel 1 and Growl in Channel 2, Low and High work
together to alter the mid-range content. By boosting Low and High, you get a
“smiling” frequency curve (mid-range cut), while cutting Low and High gives you a
bell-shaped curve (mid-range boost).
Low
Boost or cut ±12dB by turning from the center point (12 o’clock).
High
Boost or cut ±12dB by turning from the center point (12 o’clock).
Boost
For solos, you can remotely increase your output level via the footswitch. This
“clean” boost changes only the volume level, not the tonality or amount of overdrive.
Increase from minimum (0dB) to maximum (9dB). Note: When the footswitch is not
connected, the Boost function will be on, so remember to adjust its level accordingly.
Reverb
The top-of-the-line, full-length Accutronics™ 6-spring reverb can be remotely activat-
ed via the footswitch. Increase from the minimum point (7 o’clock). Note: When the
footswitch is not connected, the Reverb will be on, so remember to adjust its level
accordingly.
Link
Link works in conjunction with the Footswitch to remotely activate Boost and Reverb.
This unique feature connects the two functions. When Link is engaged, Boost and
Reverb
work in tandem
. For solos, in particular, this gives you the ability of not only
increasing your volume, but increasing the
size
of your sound as well. Depending on
its orientation, Link gives you 3 options:
1. Boost only: Disengage Link. Adjust Boost to desired level.
2. Reverb only: Engage Link. Set Reverb to desired level; set Boost at minimum.
3. Boost and Reverb: Engage Link. Set each at desired amount.
5
For separate footswitchable Boost and Reverb functions, there’s a 4th option:
Use an outboard reverb unit through the Effect Loop. The Trademark 60’s Footswitch
can then control each separately: Effect Loop for Reverb; Boost/Reverb for Boost.
Remember
: if the footswitch is not connected, Boost and Reverb will both be on.
REAR PANEL
Fuse
Fuse holder located inside A/C cord receptacle. You must remove power cord to
change fuse. Replace with similar type & same value. Amps from 100-120V: use 3A.
Amps from 220-240V: use 1.6A.
Headphone
The Headphone output overrides the speaker for undisturbed (and non-disturbing)
practicing. It can also be used as a 1/4" direct out, should an XLR input not be avail-
able on your recorder. You can then use your headphones through the mixer.
Speaker
By incorporating Tech 21’s exclusive technology with our special design 12” speaker,
the Trademark 60 gives you the speaker cabinet configuration associated with each
tube amp style --ranging from a tightly focused open-back 1x12 to a big and smooth
closed-back 4x12.
If an external speaker cabinet should be desired, simply plug in the speaker cable
from the external cabinet. This will defeat the internal speaker. We do not recom-
mend using a speaker rated at less than 8 Ohms, as a 4-Ohm speaker could cause
undesirable distortion and potentially overheat the amp. Using a 16-Ohm speaker
may result in loss of power.
Note:
The Trademark 60’s speaker is specifically
designed to complement our specialized circuitry. Therefore, using a standard
commercial speaker may result in a drastic change of sound. For recommendations,
please contact Tech 21’s technical support department.
6
DESIGNED AND MANUFAC
TECH 2
CHASSIS MAY GET HOT FROM HEA
SPEAKER
8 OHM
HEAD
PHONE
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
RISQUE DE CHOC ELECTRIQUE. NE PAS
OUVRIR.
DO NOT EXPOSE THIS EQUIPMENT TO RAIN
OR MOISTURE. NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
3A/117V
F 1.6A/250V
FUSE
AC
100V ~ 50/60 HZ
120W
AC
117V ~ 60 HZ
120VA
AC
230V ~ 50 HZ
120VA
AC
240V ~ 50 HZ
120VA
MODEL #TM- 60
CAUTION
: DISCONNECT POWER
CORD BEFORE CHANGING FUSE.
ATTENTION
: DEBRANCHER
AVANT DE REMPLACER LE FUSIBLE.
CAUTION
: REPLACE FUSE WITH
SAME TYPE AND RATING.
ATTENTION
: REMPLACER PAR
UN FUSIBLE DU MEME TYPE.
