Tecfluid AD Series Instruction Manual Download Page 16 | Manualshive

Page: 16 / 32

background image

16

12.1

Power supply and analog output

The connection is made in the terminal block. The positive terminal of the power supply is
connected to the po and the positive terminal of the load in the position -. The
negative terminals of the power supply and the load are connected together. The instrument
works in a 2-wire system, that is, the supply and signal line is the same. It is recommended
to use a twisted pair wiring or shielded cable to avoid interferences in the current loop.

13 4-WIRE

CONNECTION

If Direct Current power supply for the transmitter is not available in the installation, it will be
necessary to incorporate an additional power supply as in the following ﬁgure.

Power

supply

12 to 36 VDC

«
...
14
15
16
17
18
...
»

Summary of Contents for AD Series

































Reviews:

No comments

Related manuals for AD Series

Brand: Bamo Pages: 8

Brand: NARDA Pages: 64

Brand: E Instruments Pages: 2

Brand: Axio MET Pages: 5

PRO VPR100 Series

Brand: CTC Union Pages: 10

Brand: PCB Piezotronics Pages: 15

Brand: Sercel Pages: 63

Brand: M & I Instruments Pages: 3

Brand: Interacoustics Pages: 60

Alta Site Survey Tool

Brand: Monnit Pages: 15

Brand: SBS Pages: 17

RHEASREG KLSW-3

Brand: S+S Regeltechnik Pages: 32

Brand: Kirby Morgan Pages: 101

Brand: BASI Pages: 69

Brand: Trotec Pages: 3

Brand: STATICO Pages: 21

Brand: Veeder-Root Pages: 12

zelsius C5 -IUF

Brand: Zenner Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands