TEC TEC B-670 SERIES Maintenance Manual Download Page 9

Page: 9 / 89

2-5

EM18-33017

2. MAJOR UNIT REPLACEMENT

4) When replacing the stepping motor, place the platen belt around the pinion gear first, then the feed

roller belt, so that the partition is positioned between the two belts. Press down on the stepping motor
with 3.5 Kg

300 g force and secure it so the platen belt and feed roller belt have no slack, are

engaged ,and evenly tense.

5) Reassemble in the reverse order of removal.

Screw (FL-4x6)

Front Plate

Screw (FL-4x6)

Platen Belt

Feed Roller Belt

Screw (FL-4x6)

Fig. 2-6

CPU PC Board

CN14

Screw (SM-4x10C)

Stepping Motor

Fig. 2-7

2.3 REPLACING THE STEPPING MOTOR

1) Remove the 4 screws (FL-4x6) to detach the front plate.

2) Disconnect the cable from CN14 on the CPU PC board.

3) Remove the two screws (SM-4x10C), take the two belts off the pinion gear, and remove the stepping

motor.

2.3 REPLACING THE STEPPING MOTOR

Summary of Contents for TEC B-670 SERIES


























































































Search results

Summary of Contents for TEC B-670 SERIES

Reviews:

Related manuals for TEC B-670 SERIES

Brands by name

Popular brands

TEC TEC B-670 SERIES, Maintenance Manual

Search results

Summary of Contents for TEC B-670 SERIES

Reviews:

Related manuals for TEC B-670 SERIES

Brands by name

Popular brands