TEC B-370 Series Maintenance Manual Download Page 20

Page: 20 / 89

3-2

EM18-33012

3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENT

Reassemble in the reverse order of removal.

10. Following procedure should be employed with your PC after this.

11. Set the DIP SW. on the BPC PC board for the I/O address according to your PC.

12. Install the BPC PC board on the expansion port bus line of your PC.

13. Connect the printer cable mentioned in step 5 to the BPC PC board.

14. Insert the attached FDK into the FDD and install the data in the hard disk. Since the installation

procedure is different between MS-DOS

and Windows

, refer to each owner’s manual.

15. Perform a motion check.

* Microsoft Windows and MS-DOS are registered trademark of Microsoft Corporation.

Fig. 3-2

3.1 HIGH SPEED PC INTERFACE BOARD (B-4800-PC-QM)

Connect the printer cable to the connector (CN1) on the BPE PC board.

Put the cable strain relief of the printer cable in the notch of the cable support plate. Secure the cable
strain relief to the cable support plate by turning the nut.

Attach the cable support plate to the printer with the FL3x5 screws removed in step 2.

Connector (CN1)

BPE PC Board

Printer Cable

Cable Support Plate

Screw (FL-3x5)

Nut

Cable Strain Relief

Summary of Contents for B-370 Series


























































































Search results

Summary of Contents for B-370 Series

Reviews:

Related manuals for B-370 Series

Brands by name

Popular brands

TEC B-370 Series, Maintenance Manual

Search results

Summary of Contents for B-370 Series

Reviews:

Related manuals for B-370 Series

Brands by name

Popular brands