Team Play Fun Stop Photos Step By Step Assembly Instructions Download

Page: 1 / 19

Page 1 of 19

Step-‐by-‐Step Assembly Instructions

(with photos)

Page

Unpack the Photo Booth .................................................................................................................... 2

Secure the Power Cord ....................................................................................................................... 3

Install the Camera Topper ................................................................................................................ 4

Load Paper into the Printers ............................................................................................................ 8

Load the Ink Film and Ink Tray ..................................................................................................... 13

Printer Power Button ....................................................................................................................... 18

Meter and Test Service Buttons .................................................................................................... 19

Summary of Contents for Fun Stop Photos



















