Team Electronic TeCom-PRO Freenet, Manual

Page: 5 / 12

30
31
Frequency Inversion
This function is only useful for the commerical radio version.
To inverse the transmission and receiption frequency, hold the frequency-inversion key [
# T-R ] for
about 2 seconds. The letter R will be visible in the upper row of the LC display.
To deactivate the frequency inverse function, hold the frequency inversion key [# T-R] until the letter
R in the LC display disappears.
Attention:
Channel- / Frequency-Mode Switch
The TeCom-XP PRO can be switched between the channel mode and the frequency mode by holding
the confirmation key [ENTER] when powering on the radio. This feature is only available in the
commercial version.
Channel Mode
The programmed channel number is displayed (
CH--001 - CH--128 ).
Frequency Modes
The actual frequency is shown in the display. There are two different frequency modes available. To
switch between these two modes press the VFO/MR key [VFO/MR].
manual : the frequency can be set via key pad or by the rotary channel selector.
programmed : the programmed frequency can be seen in the middle of the display. On the right side,
the channel number is shown. The channels are changed with the rotary channel
selector.
Store Manually Set Frequency
This feature is only available in the commercial radio version.
In the manual frequency mode, select the frequency that you want to store. Press the menu key
[MENU], followed by the VFO/MR key [VFO/MR]. The channel number on the right side starts blinking.
Set the channel number where the frequency should be stored with the rotary channel selector and
confirm your entry by pressing the VFO/MR key [VFO/MR].
Delete Stored Frequency
This feature is only available in the commercial radio version.
In the programmed frequency mode, power the radio off. Hold the VFO/MR key while turning the radio
back on. The symbol „
DEL? “ appears in the display and the channel number on the right side starts
blinking. Set the channel to be deleted with the rotary channel selector and confirm your selection
with the confirmation key [ENTER]. The symbol „
YES ? “ appears in the display. To delete the channel
press the confirmation key [ENTER]. For a short time the symbol „
DELETE “ shows in the display.
More channels can now be deleted if necessary.
To leave the delete mode, press the menu key [MENU] or the VFO/MR key [VFO/MR ].
Delete all Settings of the Frequency Mode
This feature is only available in the commercial radio version.
Hold the menu key [MENU] while powering the radio on. The symbol „ RESET? “ appears in the LC
display. Confirm your selection by pressing the confirmation key [ENTER] and select the option
„ VFO ? “ with the rotary channel selector. Delete all settings of the frequency mode by pressing the
confirmation key [ENTER].
Delete all Settings
This feature is only available in the commercial radio version.
Hold the menu key [MENU] while powering the radio on. The symbol „ RESET? “ appears in the LC
display. Confirm your selection by pressing the confirmation key [ENTER] and select the option „
FULL? “
with the rotary channel selector. Delete all settings by pressing the confirmation key [ENTER].
1750 kHz Call Tone
The 1750 kHz Call Tone, for repeater operation, can be send by holding the orange button while
pressing the PTT key (for ham radio).
Advanced Functions
Channel Mode
In the following, the advanced functions, their parameters and the menu navigation will be explained.
The three keys above the numerical key pad ( [MENU], [ENTER] and [VFO/MR] are used for the
navigation through the menu.
[MENU] opens the menu. To select a menu function, press one of the numerical keys, which have
menu function.
[ENTER] confirms your selection.
[VFO/MR] closes the menu.
The actual selection is displayed. TeCom-PRO contains 21 functions in total. The functions 1 - 10 can
be selected via the keypad or the rotary channel selector, while the functions 11 - 21 can only be set
with the rotary channel selector.
Scan all Available Channels (01)
To scan all available channels, starting from the current channel, press the menu key [MENU] followed
by the channel scan key [2 SCAN]. On occupied channels, the scan function stops. When and how the
scan function continues, depends on the setting of Scan Types (see further down).
To stop the scan function press the PTT key or the confirmation key [ENTER].
Scan Priority Channels (02)
All programmed channels can be added to the scan list. The function Scan Priority Channel scans only
the channels of the scan list. Channels can be added to the list via the software or the programming
mode (step #7).
To activate the Priority Channel Scan press the menu key [MENU] and the Priority Scan Key [1 SCAN].
All channels of the scan list are constantly scanned in ring mode for signals. How the scan function reacts
once an occupied channel is detected, depends on the setup of the function Scan Type (see below).
To deactivate the priority scan function press the PTT key or the confirmation key [ENTER].
VOX Sensitivity (03)
The VOX sensitivity consists of 9 levels with increasing sensitivity from 1 to 9. To turn off the VOX
function, set the value „
OFF “.
To set the VOX function press the menu key [MENU] followed by the VOX key [3 VOX]. The display
reads „
VOX ?
“. To enter the VOX mode press the confirmation key [ENTER]. Now, set the desired
value via the key pad or the channel selector. Store your selection by pressing the confirmation key
[ENTER] and the VFO/MR key. To leave the menu press the VFO/MR key again.