background image

English

English

22

23

PTT-ID (

BOT/EOT/Both

)

The TeCom-IP3 can transmit a DTMF code via PTT-ID. Transmission of the code is
triggered by the PTT key. Each operation of the PTT key transmits the code. 

BOT

: The signal is transmitted upon pressing the PTT key.

EOT

: The signal is transmitted upon releasing the PTT key.

Both

: The signal is transmitted upon pressing and releasing the PTT key.

Priority Channel (

Priv CH

)

The priority channel can be selected out of the available channels. This is of impor-
tance for the function 

priority scan

.

DTMF Code (

ANI

The DTMF code can contain a maximum of 8 digits, composed of the digits 0-9. 

VOX (

On/Off

)

The voice activated transmission of the the signal, i.e. transmission without the PTT
key, is activated by the setting 

ON

. The radio automatically switches to transmission

mode once the signal has a certain strength. 

VOX Sensitivity (

VOX Level

)

The VOX sensitivity defines the threshold of the signal strength that is required to
start the automatic transmission. 
On level 1, the signal must be very strong to trigger the VOX function. At level 9 the
VOX function reacts the most sensitive. 

VOX Delay (

Delay

In VOX mode, after the signal ends, the radio remains in transmission mode for a
certain time before it switches back to reception mode. This avoids constant swit-
ching back and forth between transmission and reception mode when a pause du-
ring talking gets a little bit longer. You can set the delay time to the following
values: 0.3 / 0.5 / 1 / 1.5 / 2 / 6 seconds.  

Tail Eliminate

Under certain circumstances, a clicking sound will be audible when the radio swit-
ches between transmission and reception mode. To diminish this occurence, the
tail eliminate function is useful. These options are available: 

120° phase shift

180°

phase shift

240° phase shift

Freq eliminate tail

Beep Tone (

On/Off

)

A beep tone informs you about a change of status, e.g. turning the radio on, low
battery, selection of an empty channel, activation or deactivation of a function by
pressing the PF1 / PF2 key, expiration of TOT. 

Time-Out-Timer (

TOT

)

Excessive transmission without interruptions will increase the power consumption
and the temperature of the radio drastically. The Time-Out-Timer will restrict the trans-
mission time (between 30-300s in 30-seconds-steps). After expiration of the selected
time period, the radio automatically aborts transmission. After release of the PTT key,
it is possible to transmit again.  

Battery Saving Function (

Power Save

)

The TeCom-IP3 is equipped with a battery saving function to reduce power con-
sumption in standby mode. After a certain time without any operation and no recep-
tion of a signal, the radio switches to standby mode, that provides the radio with as
little as possible current to not turn off. Once a signal is received or a operation per-
formed, the radio switches back to normal operation mode. 
You can select between the ratio of normal mode and standby mode (1:1 - 1:10),
with 1:10 allowing a maximum of power saving. 

Roger Tone (

Roger Tone

)

The roger tone, which is transmitted when releasing the PTT, confirms the end of
the message for all other stations on the same channel with a short signal. 

Voice Annunciation (

Voice

)

The english voice annunciation announces the actual channel number and the on-
state when turning the radio on. 

DTMF

The following settings for the DTMF function are possible: 
> tone length of the first digit (First Digit Time) - 50-4500ms in 50ms-steps
> time between the digits (Digit Inter Time) - 25-6400ms in 25ms-steps
> delay between pressing the PTT key and transmission of the DTMF code 

(Digit Delay Time)  - 25-6400ms in 25ms-steps

> DTMF signal audible at the transmitting radio (DTMF Side Tone)

CONNECTION

The TeCom-IP3 is equipped with a Motorola-compatible con-
nector (3.5 / 2.5 mm - stereo / stereo) that is used for ear-
/headphones and the data transfer cable for the software
T-UP31. 

For further accessories please check the actual TEAM 

catalogue or web site. 

tecom-ip3_manual_3:Layout 1  7/24/2015  12:37 PM  Page 22

Summary of Contents for TeCom-IP3


























Reviews: