TDT VR2020 Series Initial Start-Up Manual Download Page 2

 

 

Note 

 

The EU declaraction of conformity can be downloaded via 

download.tdt.de

 while the manual is directly accessible 

vi

https://tdt.router/manual

 or 

https://192.168.0.50/manual

 

1

 

 Safety instructions 

This documentation contains instructions that need to be complied with for the safety of the user and/or to prevent damage to 
the VR2020 series.  

As part of ongoing security testing TDT always strives to design its products as secure as possible and attaches great importance 
to compliance with current safety and quality standards during development and regular firmware updates. 
 

1.1

 

General safety instructions 

 

The operation of the router is only permitted with the intended voltage supply. 

 

Heat should be avoided despite low heat build-up in order to prevent damage to the device. 

 

The router should not be put into operation near highly flammable or explosive gases/liquids as with all electrical 
equipment. 

 

Do not use in wet or splash-endangered areas as this could result in electric shocks and/or short-circuiting 

 

Fluids entering the chassis are to be avoided. 

 

Ensure to turn off the voltage supply before opening the housing cover in order to avoid danger to the user and 

damage to the device. 

 

There may be sharp edges and tips inside the router, so careful handling is recommended. 

 

Only use the VR2020 router and its attachments in a flawless and undamaged condition. 

 

Repairs may only be held by technicians authorized by the manufacturer. 

 

The warranty claim expires due to modifications / repairs carried out by the customer. 

 

The device has to be immediately shut down and separated from the power supply if malfunctions / damage or the 

cause of another danger is suspected. 

1.2

 

Safety instructions for devices with cellular equipment 

If the router contains a GSM modem and/or WLAN transmitter module, the following must also be considered: 

 

 

IMPORTANT!

 Mobile radio routers work with radio signals based on cellular networks. It cannot be guaranteed a 

connection  can  be  established  in  all  situations.  The  router  can  therefore 

only  be  used  conditionally  for  critical 

communication

.  

 

Antennas should be placed at a distance of at least one meter away from people. 

 

The router must not be used in hospitals or in places where medical equipment is installed. Medical equipment 

usually reacts very sensitively to high-frequency radio waves. 

 

Cardiac pacemakers and / or hearing aids can be disrupted or destroyed by interferences of mobile radio or WLAN 
routers. People using such aids should not be near the router when it is in operation and hold the minimum distance 

of at least 25 centimeters. 

 

Mobile radio or WLAN routers must not be used on aircrafts. The operation of radio transmission systems is 
generally prohibited on planes in order to avoid a disturbance of the electronics. 

 

Mobile radio or WLAN routers receive and transmit high-frequency radiation while they are in operation. It should be 
noted that interferences may occur when the router is put near electrical devices (e.g. microwaves, televisions, etc.) or 
other insufficiently shielded equipment. 

 

Only insert or replace the SIM card in a voltage-free state.

Summary of Contents for VR2020 Series









Reviews: