background image

A-4

A

ppendix

 A    

c

ompLiAnce

 / e

miSSion

 S

tAtementS

DISCLAIMER

The manufacturer of the Automated Teller Machine (ATM) product(s) described herein makes no representations 

or warranties, either expressed or implied, by or with respect to anything in this manual, and shall not be liable for 

any implied warranties of fitness for a particular purpose or for any indirect, special, or consequential damages. 

Information in this document is subject to change without notice and does not represent a commitment on the 

part of the manufacturer.

e

miSSionS

 (emi)

(US Requirements)

This  device  complies  with  Part  15  of  the  FCC 

rules.  Operation is subject to the following two (2) 

conditions: 

1)  This device may not cause harmful interference.

2)  This device must accept any interference received, 

including  interference  that  may  cause  undesired 

operation.

** CAUTION **

Changes or modifications not expressly approved by 

Triton Systems could void the regulatory compliance 

approval and the warranty. Use of this product in a 

manner other than those described in this manual 

may result in personal injury!

n

ote

:

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 

15 of FCC rules.  These limits are designed to provide reasonable protection against harmful interference when 

the equipment is operated in a commercial environment.  This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications.  Operation of this equipment in a residential area is likely to cause harmful 

interference in which case the user will be required to correct the interference at his own expense.  Changes or 

modifications to this unit not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment.

c

AnAdiAn

 r

equirementS

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set 

in the Radio Interference Regulations of the Canadian Department of Communications. This Class A digital 

apparatus complies with Canadian ICES-003.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils 

numeriques de la Class A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des 

Communications du Canada.  Cet appareil numerique de la classe A est conforme a la norme NMB-003 Canada.

uK / A

uStrALiA

 / S

outh

 A

fricA

  r

equirementS

Warning:

This is a Class A product.  In a domestic environment, this product may cause radio interference in which case 

the user may be required to take adequate measures. 

Summary of Contents for Triton VersaSafe



























Reviews: