manualshive.com logo in svg

TDK-Lambda PHV Series, Operator'S Manual, Page: 5 / 38

Share
Download
TDK-Lambda PHV Series Operator'S Manual Download Page 5

 

 

 

2 

 

83550001 Revision C 

 

5.1.20.

 

Analog LED (Ref 20) ...............................................................................................................20

 

5.1.21.

 

Analog/Digital Remote Switch (Ref 21) ....................................................................................20

 

5.1.22.

 

Digital LED (Ref 22) ................................................................................................................20

 

5.1.23.

 

Busy LED (Ref 23) ..................................................................................................................20

 

5.2.

 

Rear Panel Layout ...................................................................................................................20

 

5.2.1.

 

HV Output Connector (Ref 1) ..................................................................................................22

 

5.2.2.

 

HV Output Return (Ref 2) ........................................................................................................22

 

5.2.3.

 

Optional Digital Interface (Ref 3) .............................................................................................22

 

5.2.4.

 

Remote Analog Connector (Ref 4) ..........................................................................................22

 

5.2.5.

 

Safety Ground (Ref 5) .............................................................................................................22

 

5.2.6.

 

AC Line Fuse (Ref 6) ...............................................................................................................22

 

5.2.7.

 

AC Input Connector (Ref 7) .....................................................................................................22

 

 

6.

 

LOCAL OPERATION

 ..............................................................................................................24

 

6.1.

 

Set the Control Mode ..............................................................................................................24

 

6.2.

 

Turn on AC power ...................................................................................................................24

 

6.3.

 

Select desired output polarity ..................................................................................................24

 

6.4.

 

Set the output OVP Limit .........................................................................................................24

 

6.5.

 

Set the desired output voltage/current levels ...........................................................................24

 

6.6.

 

Turning ON the output .............................................................................................................24

 

6.7.

 

CC/CV Mode Indication ...........................................................................................................25

 

6.8.

 

Turning the unit OFF ...............................................................................................................25

 

 

7.

 

ANALOG REMOTE CONTROL OPERATION

 ........................................................................26

 

7.1.

 

The Non-Isolated Analog Interface (ANA option) .....................................................................26

 

7.1.1.

 

Typical Remote Operation .......................................................................................................27

 

7.1.2.

 

Remote HV ON/OFF with LOCAL voltage/current controls (ANA option only) .........................27

 

7.1.3.

 

HV Output is always ON, REMOTE Voltage and Current programming (ANA option only) ......27

 

7.1.4.

 

HV Output is always ON, REMOTE Voltage programming, Current set to 100% rated value ..27

 

7.2.

 

Isolated Analog Programming (INA option)..............................................................................28

 

 

8.

 

DIGITAL REMOTE CONTROL OPERATION

 .........................................................................30

 

 

9.

 

PARALLEL OPERATION

 .......................................................................................................32

 

9.1.

 

Parallel Master Slave operation with the Remote Analog Interface 

– Option 1 ........................32

 

9.2.

 

Parallel Master Slave operation with the Remote Analog Interface 

– Option 2 ........................32

 

 

Summary of Contents for PHV Series







































Reviews:

No comments