TDK-Lambda LS100 Series Instruction Manual Download Page 13

 

12 

 

   

 

 

 

 

 

 

     

TDK-Lambda 

LS 

25-150 

Series 

INSTRUCTION MANUAL

 

7. External Fuse Rating 

Refer to the following fuse rating when selecting the external input fuse. Surge current flows when input turns on.   
Fuse rating is specified by Inrush Current value at input turn on. Do not select the fuse according to input current (rms) 
values under the actual load condition. 

 
 LS25 

  : F1.6A 

250V 

 

LS35, LS50 

T2A , 250V 

 

 LS75 

  : T2.5A 

250V 

 LS100 

 : F4A 

250V 

 LS150 

 : F5A 

250V 

 

 

8. Before concluding that the unit is at fault, make the following checks. 

z

 

Check if the rated input voltage is connected. 

z

 

Check if the wiring of input and output is correct. 

z

 

Check if the wire size is correct. 

z

 

Check if the output voltage trimmer (V.ADJ) is properly adjusted. 

z

 

Check if the output current and output wattage does not exceed the specification. 

z

 

Ensure that a large capacitor is not connected across the output terminals. Please use within maximum capacitance 
shown below. 

 
 

Maximum external capacitance 

MODEL 

3.3V 

5V 12V  15V  24V 36V 48V 

LS25 10,000uF 

5,000uF 

2,000uF 

1,000uF 500uF 

LS35~LS50 10,000uF 

5,000uF 

2,000uF 

500uF 

LS75~LS150 10,000uF 

5,000uF 

1,000uF 

 
NOTE : It is normal to hear audible noise from power-supply under Dynamic Load operation or if the input voltage 
waveform is not sinusoidal. 
 

 
 
9. Warranty Condition 
 

This product is under warranty for 3 years (based on 8 hours/day operation) from the date of shipment. During the                       
warranty period, TDK-Lambda will, at it’s option, either repair or replace products prove to be defective.   

 
  Warranty applies but not limited to the following. 

(1)

 

Average operating temperature (ambient temperature of the power supply unit) is under 40

o

C. 

(2)

 

Average load factor is 80% or less. 

(3)

 

Installation method : Standard installation. 

 

  Following cases are not covered by warranty. 

(1)

 

Improper usage and mis-handling like dropping or applying shock to the unit and defects from operation           
exceeding specification of the product. 

(2)

 

Defects resulting from natural disaster (fire, flood). 

(3)

 

Unauthorized modification or repair. 

 

Summary of Contents for LS100 Series














Reviews: