TDK-Lambda EZA2500 Series Quick Manual Download

Page: 8 / 17

- 8 -

TDK-Lambda

EZA2500 series

Quick Manual / Practical (III)

3) Checking the operation status using CNVCommCC

It is possible to check the operating status during EZA waiting and operating via RS485.

The following describes how to check the alarm contents using CNVCommCC.

Start CNVCommCC and confirm that it can communicate with EZA.

①

Click "Main" tab and click "READ" of "[02] Converter status" to display the current

status of EZA..

②

Click “READ” in "[10]Converter Meter 1" to display the details of voltage, current,

power and internal temperature of the battery side and grid side at the time of clicking.

③

To update and display all parameters on the screen, click

“

READ ALL

”

at the

bottom left of the screen.

②

Checking the details of the Converter Status.

①

Start CNVCommCC.

①

②

③

Summary of Contents for EZA2500 Series


















Search results

Summary of Contents for EZA2500 Series

Reviews:

Related manuals for EZA2500 Series

Brands by name

Popular brands

TDK-Lambda EZA2500 Series, Quick Manual

Search results

Summary of Contents for EZA2500 Series

Reviews:

Related manuals for EZA2500 Series

Brands by name

Popular brands