TDK-Lambda EZA11K-320240 Quick Manual Download Page 21

Page: 21 / 23

- 21 -

TDK-Lambda

EZA11K series

Quick Manual / Practical(I)

Parameter

Function

Operation mode

Symbol

Name

LBV

Limit of Battery
Volts for
Discharging

Set the battery discharge lower
limit voltage of the battery over
discharge protection function

-Manual grid CV
-Manual grid CV with battery CC.
-Automatic grid CV
-Automatic grid CV with battery
CC.

DLD

Deviation of
Volts for
Warning of
Discharging
Lower Limit

Set the warning voltage to
inform you that the battery is
almost fully discharged. When
Battery Volt<LBV+DLD,
Warning signal is outputted.(Set
1 in Bit10 of CST)

-Manual grid CV
-Manual grid CV with battery CC.
-Automatic grid CV
-Automatic grid CV with battery
CC

DCD

Deviation of
Volts for
Cancel
Warning of
Discharging
Lower Limit

When Battery Volt
>LBV+DLD+DCD, Warning
signal is canceled. (Set 0 in
Bit10 of CST)

-Manual grid CV
-Manual grid CV with battery CC.
-Automatic grid CV
-Automatic grid CV with battery
CC.

*Deadzone: Converter is held in equilibrium operation that no operations neither generation
(Charge) nor regeneration (Discharge).

Summary of Contents for EZA11K-320240
























Search results

Summary of Contents for EZA11K-320240

Reviews:

Related manuals for EZA11K-320240

Brands by name

Popular brands

TDK-Lambda EZA11K-320240, Quick Manual

Search results

Summary of Contents for EZA11K-320240

Reviews:

Related manuals for EZA11K-320240

Brands by name

Popular brands