TCS PDS Series Product Information Download Page 13

Page: 13 / 16

PI_GB_PES_PDS_Art0015689_1v0.doc 13

10/2005

Method 2

In-house station accessible

LED illuminates

Press briefly

LED flashes

programming
mode
of system
switched on

Lift handset

press briefly,

replace handset

at in-house station

ring tone sounds

at in-house station

at front-door and in-house station

bell button
programmed

Press briefly

LED illuminates

programming
mode
of system
switched off

Programming the other bell buttons:

•

Step

•

repeat step

each time for additional bell buttons where necessary

•

complete the programming of all buttons with step

TCS TürControlSysteme AG

•

Geschwister-Scholl-Str. 7

•

39307 Genthin

Subject to change without notice.

Phone: +49 39 33 / 87 99 10

•

Fax: +49 39 33 / 87 99 11

•

www.tcs-germany.com

Art.Nr. 0015689 Version 1.0 mi

Summary of Contents for PDS Series

















Search results

Summary of Contents for PDS Series

Reviews:

Related manuals for PDS Series

Brands by name

Popular brands

TCS PDS Series, Product Information

Search results

Summary of Contents for PDS Series

Reviews:

Related manuals for PDS Series

Brands by name

Popular brands