background image

02/2015 

 

TCS TürControlSysteme AG, TCS Hotline Germany:  +49 (0) 4194 9881-188

 

Subject to technical changes. 

E-Mail: [email protected], www.tcsag.de

 

PI_IVH3222-0140_uk  3 A 

 

Connect the lines   

  Minimize the length of the lines above the 

lower cover to place the lines without any 
problems and do not clamp the lines when 
snapping-on the upper cover. 

  Connect the lines according to the labeling 

(in the lower cover): a b E P M V1 V2 (from 
the bottom to the top),  
floor push button to a and E. 

 
See wiring diagram on page  9 

 
 

 

 

Place matching resistor 

The video indoor station IVH3222 is not suitable 
for the operation at the end of a strand ex 
works. Switch in position OFF. 

  

  For the operation with further up streamed 

video indoor stations slide the switch in posi-
tion ON. 

 

 

  

 

 

Close the device 

  Set on the upper cover at both adjustment 

increments of the lower cover (

1

). 

  Snap-on the upper cover below with slight 

pressure (

2

 

 

 

 

Connect the handset 

  Plug the Western socket of the handset cord 

into the socket at the underside of the tele-
phone. 

 

 

 

floor push button 

ON 

OFF 

Summary of Contents for IVH3222

















Reviews: