TCS ISH3030 Product Information Download Page 10

Page: 10 / 16

07/2013

TCS TürControlSysteme AG

Subject to technical changes.

Mail: [email protected]

ISH3030-0140 UK 2A

Connection diagram 2-wire technique

Connection diagram 3-wire technique

Replacing an ISH1030 or TTS1 by an ISH3030



The floor push-button have to be connected always to the a-wire.



In case of a parallel circuit both telephones have to be replaced by the ISH3030.

Commissioning



Install the devices of the system voltage-free and completely.



Proof the a-, b- and P-wire against each other on short-circuit.



Switch on the main voltage.

Note:
If the floor push-button is not working, proof, i fit is connected to the a-wire of the power
supply and control unit.

Settings

Pre-adjusted times

communication time

max. 2 min

flashing period of the green LED, if the voice
channal is busy after lifting the handset

2 sec

3 x flashing

internal standby time, if the device is calling or
is called

around
30 sec

Summary of Contents for ISH3030

















Search results

Summary of Contents for ISH3030

Reviews:

Related manuals for ISH3030

Brands by name

Popular brands

TCS ISH3030, Product Information

Search results

Summary of Contents for ISH3030

Reviews:

Related manuals for ISH3030

Brands by name

Popular brands