TCL TAC-42CF Service Manual Download Page 6

TCL Air Conditioner Service Manual 

                                                                                             

5

Elctronic Controller 

1. Safety 

Control 

(1)  Time Delay Safety Control 

 

3 minutes delay for compressor---The compressor is ceased for 3minutes to balance the pressure in the 
refrigeration cycle in order to protect the compressor. 

 

2 minutes delay for 4-way valve---The 4-way valve is ceased for 2 minutes to prevent the 
refrigerant-gas abnormal noise when the HEATING operation is OFF or switch to the other operation 
mode. 

 

20 seconds delay for indoor fan--- When the assistant thermistor turns off, the indoor fan operates in 
low speed for 20 seconds to release the heat of indoor unit. 

(2)  Indoor Pipe Temperature Sensor Frost Prevention Control 

When the indoor pipe temperature sensor reads 0

  or below for 5 minutes, the indoor pipe temperature 

sensor frost prevention control starts. The compressor and outdoor fan stop and indoor fan operates at high 
speed for 3 minutes. After that, if the indoor pipe temperature sensor reads  less than 5

 this control 

prolonged until the indoor pipe temperature sensor reads 5

 or more. 

(3)  High Temperature Protection Control 

During HEATING operation, the outdoor fan motor and compressor are controlled by the indoor pipe 
temperature to prevent the high temperature of compressor. 
Outdoor fan OFF: 5

6

 

Outdoor fan ON:

50

 

Compressor OFF:6

0

 

Compressor ON:

50

 

2. “

AUTO

” Mode Operation 

(1) When the “

AUTO

” mode is selected, the operation mode and initial set temperature are determined by the 

initial room temperature at start-up of the operation except to turn off the air conditioner and operates it 
again. 

(2) If the mode is change to “

AUTO

” mode from other mode, the “

AUTO

” mode doesn’t operate until compressor 

stop for more than 3 minutes. 

 
 

 
 
 
 
 
 
 

 

 In the “

AUTO

” mode , when the controller receives the up or down single of temperature, the set 

temperature can adjust by 1

  upper or lower. The biggest you can adjust by 2

  upper or lower. 

3.  “COOLING” Mode Operation 

(1)  When the COOLING mode is selected without setting temperature, the system will set the set temperature at 

26

  automatically with the AUTO FAN speed. 

(2) 

When selecting the COOLING mode operation, the system will operate according to the setting by the 
remote controller and the operation is as following: 

 

 
 

Mode 

Initial room temperature 

COOLING  

DRY 

HEATING for Heat Pump Type   
FAN for Cooling Only Type 

26

 or more 

20

 to 25 

 

Less than 20

 

Initial set temperature 

24

 

18

 

23

 

Summary of Contents for TAC-42CF


















Reviews: