EN
9
English
Chapter 3 - Installing channels
Initial setup
Initial setup involves selecting all the settings required
to be able to search for and store all the analogue
and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specified hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The first time you switch the set on, the
Initial Setup
wizard opens, which guides you through the initial
setup process. (Refer to Figure 1.)
Figure 1
Step 1: Environment setup
1.
Press
▲
/
▼
to select your language, then press
OK/►
to enter the next step.
2.
Press
▲
/
▼
to select your country, then press
OK/►
to enter the next step.
Note: If you select
France
or
Italy
, you will have to
enter the password setting menu here to set
a password. Use the numeric buttons to enter
a four-digit number as your password. (0000
is too simple to be set as your password.)
Enter the same code again to confirm the
password. After that, you will enter the next
step automatically. (In this step, you can only
press
◄
to return to the previous step.)
3.
Press
▲
/
▼
to select your location, then press
OK/►
to enter the next step.
Step 2: Network setup
1.
Press
▲
/
▼
to select your network connection type
(
Wired
or
Wireless
), then press
OK/►
to enter the
next step.
2.
Follow the guides on the screen and press the
corresponding buttons on the remote control to
proceed.
Note: You can also skip this step and step 3
by selecting
"
I do not have a network
connection
"
, and connect to the Internet later.
For details please refer to section
Network
Connection.
Step 3: Software update
1.
If the set has connected to the network
successfully, it will search for upgrade files
automatically.
2.
Follow the guides on the screen and press the
corresponding buttons on the remote control to
proceed.
Step 4: Channel installation
1.
Press
▲
/
▼
to select
Continue
to install channels.
2.
Follow the guides on the screen and press the
corresponding buttons on the remote control to
proceed.
Note: To prevent the channel installation process
from being interrupted, wait for the message
indicating that the installation is complete.
You can also skip this step by selecting
"
I don't
want to install channels
"
. In this case, to
search and store your channels you may do
an automatic channel search by following the
instructions in the next section
Performing
an automatic channel search
.
Step 5: Clock setup
If the set was not connected to the network, you can
use the numeric buttons to enter the date and time,
then select the
OK
button and press
OK
to confirm.
When the initial setup is completed, the
Congratulations
message appears. Press
OK
to
confirm.
Performing an automatic channel search
This section describes how to search and store
channels automatically. This may be done in any of
the cases below:
- you have selected "
I don't want to install channels
"
in the initial setup;
- you see "
No program info now, please search
channels first!
" in TV mode;
- you want to update your channels.
1.
In TV mode, press
on the remote control and
select
Channel > Channel scan
. Press
OK/
►
to
enter.
2.
The TV installs and arranges channels according
to your country. Press
▲
/
▼
to select
Country
, and
press
OK/
►
to enter. Enter the default password
1234 or your own password in case you have
changed the password in the
System > Lock
menu. Press
▲
/
▼
to select your country and press
OK/
►
to confirm.
3.
Press
▲
/
▼
to select
Tuner mode
, then press
OK/
►
to enter. Press
▲
/
▼
to select
Cable
,
Antenna
or
Satellite
, and press
OK/
►
to confirm.
(Note:
Satellite
option is available only in selected
models.)
4.
Follow a), b) or c) below.
- a) If you have selected
Cable
.
