TCi HGP HarmonicGuard Series Installation, Operation And Maintenance Manual Download Page 39

Page: 39 / 67

HGP Kit Manual

5.0 PQconnect

PQconnect Bluetooth

App Setup

System Requirements:

Android OS 5.0 or higher

Bluetooth 4.2

Installation Instructions

1. Download the app using your mobile device.

2. Extract the contents of the downloaded zip

folder.

3. Tap on the APK file to install. Note: The Android

system may require permission to install apps

from sources other than the Play Store.

4. A warning may appear. Click on settings and

click slider for “allow from this source.”

Pairing Instructions

1. Once installed, open the PQvision mobile app.

(You must allow PQconnect to use Bluetooth.)

Any Bluetooth capable PQconnect devices in

range will be automatically displayed on the

connection screen.

2. Tap CONNECT next to your target PQconnect

device. Each PQconnect device in the app will

be identified by their Device ID.

3. A prompt to enter the Bluetooth pairing passkey

will pop up automatically. The password is

111111.

Summary of Contents for HGP HarmonicGuard Series




































































Search results

Summary of Contents for HGP HarmonicGuard Series

Reviews:

Related manuals for HGP HarmonicGuard Series

Brands by name

Popular brands

TCi HGP HarmonicGuard Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for HGP HarmonicGuard Series

Reviews:

Related manuals for HGP HarmonicGuard Series

Brands by name

Popular brands