background image

www.tbsdtv.com 

 

 

 

7

 / 

7

 

 

Audio Encoding: AAC, MP3, MP2 

Level: AAC-LC, AAC-HE 

Channel: L +R (stereo), L/R (mono) 

Source: HDMI embedded or Line in 

 

Adjust HDMI Input 

CH 1 CLK REVERSE ~ CH 4 CLK REVERSE 

This is to adjust 4k_30hz input for channel 1 to channel 4. Normally, if your input is 1080P_60hz or lower input, 

“CH x CLK REVERSE” please set to “OFF” (OFF is the default). 

And if “CH CLK REVERSE” is OFF, 4K_30hz input might not be detected correctly (for instance, the image capture is 

not complete and the image flickers, or many “green, red” lines in the video), please switch “CH x CLK REVERSE” to 

“ON”. 

 

System 

Timing reboot: for example, if you set  “1” hour, then every 1 hour Encoder will reboot; and if you set 12 hours, 

every 12 hours Encoder reboots. If you set 28 hours, then every 28 hours Encoder reboots. And so on. 

Reset Encoder: configuration/web UI password/port reset 

Reboot Encoder 

 

 

Firmware Upgrade 

Upload “update.bin” first and then upload “upgrade.bin”, last is to reboot Encoder to activate. 

 

 

Any question about TBS2614/TBS2616, please contact with us:   

[email protected]

 

 

Summary of Contents for TBS2614








Reviews: