background image

Model LR-416B, LR-165A, & LR-25B Hoist Installation and Operation Manual 
Stock No. 036257 
Page 19 of 22 
 

 

"OPERATION OF HOIST AND PUMP"

 

WARNING: 

Operating this hoist without first understanding the proper operation procedures can 
lead to serious injury or death.  Always read and understand fully all operation manuals 
before using or operating this equipment. 

 

WARNING: 

An operation manual for the hydraulic system should be available.  The operation 
manual for the supplied hydraulic system 

MUST BE

 read and understood before 

operating this trailer. 

 

WARNING: 

Being under a raised body can result in serious injury or death should the body 
unexpectedly descend.  

Never

 position yourself or allow others to position themselves 

under a 

loaded

 body.  

Always

 prop the 

unloaded

 body up using the body prop or body 

props supplied.  

Remember,

 body props are to be used only on an 

unloaded 

body. 

 
DANGER: 

1. Stay out from under body when hoist is operating. 
2. During dumping operations, no one must be allowed to stand in or move through the 
area where the body and hoist operate or into an area where an upset load might fall. 
3. Controls must be in a safe location and operator must remain at controls during the 
dumping operation.  Controls must be permanently located in truck cab or another 
location where it is not possible to be under body during dumping operation. 
4. 

Never

 leave body raised or partly raised while the truck is unattended or while 

performing maintenance or service under body, unless body is braced to prevent 
accidental lowering. 
5. If hoist pump is direct engine driven by truck, always disengage drive when hoist is 
not in use or when moving load. 
6. 

Do not

 attempt to raise a loaded body when the vehicle is on un-level ground. 

7. Never jerk or shock a raised body to loosen a stuck load. 

 
WARNING: 

Freeing a stuck load during dumping, with the body raised, by jerking or shocking the 
truck, may cause damage to the truck, serious injury or death.  

Never

 drive forward or 

rearward and stop quickly with the load up or otherwise shock the load.  If a load is 
stuck in the body, lower the body, then free the load. 

 
WARNING: 

Attempting to dump a load on un-level ground may cause the truck to over turn, and 
can result in damage, serious injury or death.  

Always

 dump the load on ground that is 

level front to rear as well as level side to side. 

 

 

Summary of Contents for Rugby LR-165A Rugby LR-25B























Reviews:

Related manuals for Rugby LR-165A Rugby LR-25B