background image

Operator’s Manual 

Chipper Shredders

10

Check for parts online at www.tazztools.com or call 800-345-6007 M-F 8-5

A

B

A

C

B

FIGURE 1

D

A

B

C

1.  Position the kick stand (A) 

underneath the engine 

with the loop of the kick 

stand pointing away from 

the wheel axle (B). 

2.  Using the four M8-1.25 

X 40 bolts (C), eight M8 

washers (D) and four 

M8-1.25 nuts (E), secure 

the kick stand to the base 

plate of the engine.

A

C

D

E

B

ASSEMBLY

Install Kick Stand (SEE FIGURE 1)

Install the Wheels (SEE FIGURE 2)

1.   Slide the wheel onto the axle (B). 
2.   Slide the 12mm washer  (A) onto the axle so that it sits 

against the wheel. 

3.   Insert the cotter pin (C) into the hole in the end of the 

axle. Bend the cotter pin over to secure the wheel to the 

axle.

FIGURE 2

Install Chipper Cone (SEE FIGURE 3)

1.  Position the chipper cone (A) over the three M8-1.25 

threaded studs protruding from the engine plate, and 

attach using three M8-1.25 flange nuts (B). 

2.  Rotate cone and cone base away from engine so cone 

does not contact engine.

3.  Tighten the flange nuts securely.

FIGURE 3

Install the Hopper

1.  Remove back four M6-1.0 nuts (A) and set nuts and rear 

stud plate (B) aside. Loosen front four M6-1.0 nuts (C), do 

not need to remove. Install damper (D). SEE FIGURE 4

2.  Install hopper (E) by sliding slotted holes (F) on the 

front side of hopper onto the four front studs (G) with 

loosened nuts. SEE FIGURE 5

3.  Reinstall rear stud plate (H) and four back M6-1.0 nuts (I) 

that were previously removed in Step 1. SEE FIGURE 5

4.  Tighten all eight M6 nuts.

E

I

F

G

H

FIGURE 4

FIGURE 5

Summary of Contents for 18493

































Reviews: