INSTALLATION INSTRUCTIONS
2
3
1
4
ATTACH THE HOT AND COLD SUPPLY LINES
Make connections to water lines. Use 1/2” I.P.S. faucet connections (2) or coupling nuts (3) (not includ-
ed) with 3/8” O.D. ball-nose riser (1). Use two wrenches when tightening. Do not over tighten. Install
the weight at the lowest point of the hose to prevent it from twisting.
TURN OFF
TURN OFF
SI
LI
CO
NE
Your installation may require new supply
lines. (Supply lines are not included.)
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
REV. JULY, 2016
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
WITH OPTIONAL ESCUTCHEON
THANK YOU
FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
RECOMMENDED TOOLS:
1
Flashlight
Teflon tape Screwdrivers
Adjustable
wrench and
pipe wrench
Plumber’s putty
Safety goggles
Torque wrench
Silicone caulk
5
6
EXPLODED DIAGRAM FOR REFERENCE
MAINTENANCE
Your new faucet is designed for years of trouble-free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals as these will dull the finish and void your warranty.
FLUSHING THE WATER LINES
Turn on hot and cold water supplies. Pull the hose assembly out of the spout and remove the spray
head by unscrewing it from the hose counterclockwise. Be sure to hold the end of the hose down into
the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush water
lines for one minute. Check for leaks. Re-tighten any connections if necessary, but do not overtight-
en. Reinstall spray head by hand tightening it back onto the spray hose.
2
TURN OFF THE MAIN WATER SUPPLY
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
WARNING: READ ALL
the instructions completely before beginning.
READ ALL
warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help?
Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
COSMOS 06-8845S
SINGLE HANDLE KITCHEN FAUCET
1 - INDEX
2 - SET SCREW
3 - HANDLE
4 - CAP
5 - BONNET
6 -CAP
7 - CARTRIDGE
9 - O-RING
10 - O-RING
12 - FLANGE
13 - METAL WASHER
14 - MOUNTING NUT
15 - SCREW
16 - TUNNEL
19 - WEIGHTS
22 - BASE PLATE
24 - MOUNTING NUT
23- BOLT
18 - SPRAY ASSEMBLY
17 - INVERTER
8 - TUBE
11 - JACKET
21 - ESCUTCHEON
20 - WASHER
3
FAUCET INSTALLATION
A)
Remove old faucet. Clean sink surface in preparation for new faucet. Apply a bead of plumber’s
putty or silicone caulk around the faucet openings. Install the gasket over the three holes in your
sink.
B)
Place faucet in position on sink. From underside. Secure faucet with nut (1).
Don’t use plumber’s putty on cultured marble or other composite sinks.
Putty will discolour the sink.
B
A
