manualshive.com logo in svg

Taylor C722, Operating Instructions Manual, Page: 44 / 67

Share
Download
Taylor C722 Operating Instructions Manual Download Page 44

40

Model C722

Important: Operator Checklist

121004

Section 8

Troubleshooting Guide

PROBLEM

PROBABLE CAUSE

REMEDY

PAGE

REF.

1. No product is being

dispensed.

a. Low on mix. The MIX

OUT light is on.

a. Add mix to mix hopper.

Return to AUTO mode.

34

b. Power switch is in the

OFF position.

b. Turn power switch ON

and select AUTO.

33

c. Machine not in AUTO

mode.

c. Select AUTO and allow

machine to cycle off
before drawing product.

34

d. Beater motor is out on

reset. The BEATER
OVERLOAD message
displayed.

d. Turn machine off. Press

the reset button. Restart
the machine in AUTO.

- - -

e. Pump motor control is out

on internal overload.

e. Turn power switch off.

Remove and clean mix
pump. Allow at least two
minutes for power switch
to remain off for control to
reset. Once power is
restored, before installing
pump, press pump key
and verify the pump shaft
rotates counter-clockwise.

Note:

If this does not

correct the problem or if
rotation is clockwise, call
an authorized service
technician.

- - -

f. Feed tube or check ring

not properly installed.

f. Make sure feed tube and

rubber check ring are
properly installed.

31, 34

g. Butterfat buildup in the

pump.

g. Carefully remove the mix

pump, clean and reinstall.

36

h. Freeze-up in mix inlet

hole.

h. Call an authorized service

technician.

- - -

i. The mix pump ball crank

is broken.

i. Call an authorized service

technician.

- - -

2. No control panel functions

(power switch is ON).

a. Machine is unplugged.

a. Plug into wall receptacle.

- - -

b. Circuit breaker OFF or

blown fuse.

b. Turn the breaker ON or

replace the fuse.

- - -

Summary of Contents for C722




































































Reviews:

No comments