Taurus IS 5000 M, Manual, Page: 56 / 64

9. Repair and Maintenance
ϭϬ͘ƌƌŽƌŝŶĨŽƌŵĂƟŽŶĂŶĚƉƌŽĐĞƐƐŝŶŐ
- 33 -
10.1 Error code
ƌƌŽƌĐŽĚĞ ĞƐĐƌŝƉƟŽŶ ^ŽůƵƟŽŶƐ
F14 DC firmware over current
F15 AC firmware over current
F16
GFCI(RCD) Ac leakage
current fault
F19 All hardware failure synthesis
F23
AC leakage current is transient
over current
1. Turn off DC/AC switch, and turn on DC/AC switch 3mins
later;
2. If the fault still exists, please contact us for help.
1. Restart inverter and check whether it is in normal;
2. Seek help from us, if can't go back to normal state.
1. Check PV module connection;
2. Turn off the DC/AC switch and then wait 1~2 minute, then
turn on the DC/AC switch again;
3. Seek help from us, if can't go back to normal state.
1. Restart inverter and check whether it is in normal;
2. Seek help from us, if can't go back to normal state.
1. Please wait for a while and check whether it is normal;
2. If still same, and turn off the DC switch and AC switch and
wait for one minute and then turn on the DC/AC switch;
3. Seek help from us, if can't go back to normal state.
^ƚƌŝŶŐƚLJƉĞŝŶǀĞƌƚĞƌĚŽĞƐŶ͛ƚŶĞĞĚƌĞŐƵůĂƌŵĂŝŶƚĞŶĂŶĐĞ͘,ŽǁĞǀĞƌ͕ĚĞďƌŝƐŽƌĚƵƐƚǁŝůůĂīĞĐƚŚĞĂƚ
ƐŝŶŬ͛ƐƚŚĞƌŵĂůƉĞƌĨŽƌŵĂŶĐĞ͘/ƚŝƐďĞƩĞƌƚŽĐůĞĂŶŝƚǁŝƚŚĂƐŽŌďƌƵƐŚ͘/ĨƚŚĞƐƵƌĨĂĐĞŝƐƚŽŽĚŝƌƚLJ
ĂŶĚĂīĞĐƚƚŚĞƌĞĂĚŝŶŐŽĨ>ĂŶĚ>ůĂŵƉ͕LJŽƵĐĂŶƵƐĞǁĞƚĐůŽƚŚƚŽĐůĞĂŶŝƚƵƉ͘
/ŶǀĞƌƚĞƌŚĂƐďĞĞŶĚĞƐŝŐŶĞĚŝŶĂĐĐŽƌĚĂŶĐĞǁŝƚŚŝŶƚĞƌŶĂƟŽŶĂůŐƌŝĚƟĞĚƐƚĂŶĚĂƌĚƐĨŽƌƐĂĨĞƚLJ͕
ĂŶĚĞůĞĐƚƌŽŵĂŐŶĞƟĐĐŽŵƉĂƟďŝůŝƚLJƌĞƋƵŝƌĞŵĞŶƚƐ͘ĞĨŽƌĞĚĞůŝǀĞƌŝŶŐƚŽƚŚĞĐƵƐƚŽŵĞƌƚŚĞ
ŝŶǀĞƌƚĞƌŚĂƐďĞĞŶƐƵďũĞĐƚĞĚƚŽƐĞǀĞƌĂůƚĞƐƚƐƚŽĞŶƐƵƌĞŝƚƐŽƉƟŵĂůŽƉĞƌĂƟŽŶĂŶĚƌĞůŝĂďŝůŝƚLJ͘
/ĨƚŚĞƌĞŝƐĂŶLJĨĂŝůƵƌĞ͕ƚŚĞ>ƐĐƌĞĞŶǁŝůůĚŝƐƉůĂLJĂŶĂůĂƌŵŵĞƐƐĂŐĞ͘/ŶƚŚŝƐĐĂƐĞ͕ƚŚĞŝŶǀĞƌƚĞƌ
ŵĂLJƐƚŽƉĨĞĞĚŝŶŐĞŶĞƌŐLJŝŶƚŽƚŚĞŐƌŝĚ͘dŚĞĂůĂƌŵĚĞƐĐƌŝƉƟŽŶĂŶĚƚŚĞŝƌĐŽƌƌĞƐƉŽŶĚŝŶŐĂůĂƌŵ
messages are listed Table 10.1
.
Warning:
When the device is running, the local temperature is too high and the touch can
ĐĂƵƐĞďƵƌŶƐ͘dƵƌŶŽīƚŚĞŝŶǀĞƌƚĞƌĂŶĚǁĂŝƚĨŽƌŝƚĐŽŽůŝŶŐ͕ƚŚĞŶLJŽƵĐĂŶĐůĞĂŶĂŶĚ
maintain.
Warning:
No solvent, abrasive materials or corrosive materials can be used for cleaning
any parts of the inverter.