After Sales Support
TEL: 1300 922 271 EMAIL: [email protected]
9
3.2 Items supplied
-
Open the packaging and take out the equipment
with care.
-
Remove the packaging material and any packaging
and/or transportation braces (if available).
-
Check to see if all items are supplied.
-
Inspect the equipment and accessories for the
transport damage.
-
If possible, please keep the packaging until the end
of the guarantee period.
Important!
The equipment and packaging material are not toys. Do
not let children play with plastic bags, foils or small parts.
There is a danger of swallowing or suffocating! Do not let
children play with plastic bags, foils or small parts. There
is a danger of swallowing or suffocating.
-
Scroll saw
-
Blade guard
-
Sawdust blower facility
4. Proper use
The Scroll saw is intended for cutting square edged timber or
wood-like workpieces. Round materials may only be cut with
suitable holding devices.
The machine is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user
/ operator and not the manufacturer will be liable for any
damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications. Our
warranty will be voided if the machine is used in commercial,
trade or industrial businesses or for equivalent purposes.
The equipment is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-off wheel. To
use the equipment properly you must also observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this manual.
All persons who use and service the equipment have to be
acquainted with this manual and must be informed about the
machine’s potential hazards.
It is also imperative to observe the accident prevention
regulations in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any changes made to
the machine nor for any damage resulting from such changes.
Even when the equipment is used as prescribed it is still
impossible to eliminate certain residual risk factors. The
following hazards may arise in connection with the machine’s
construction and design:
• Harmful emissions of wood dust when used in closed
rooms.
• Contact with the blade in the uncovered cutting zone.
• Injuries (cuts) when changing the blade.
• Crushed fingers.
• Kickback.
• Tilting of the workpiece due to inadequate support.
• Touching the blade.
5. Technical data
Mains voltage: _________________________ 230 V ~ 50Hz
Power: __________________80 W S2 20 min/120 W S6 30%
Idle speed n
o
: _________________________ 400-1600 rpm
Protection type: _______________________________IP 20
Stroke: _____________________________________ 21 mm
Base area: ____________________________ 440 x 280 mm
Tilting range of table: _______________ 0° to 45° to the left
Table size: ___________________________413.5 x 253 mm
Saw blade length: ___________________________ 127 mm
Throat: ____________________________________ 406 mm
Max. cutting height at 90°: _____________________ 57 mm
Max. cutting height at 45°: _____________________ 27 mm
Weight: _____________________________________ 13 kg
Load factor:
A load factor of S2 20 min (intermittent periodic duty) means
that you may operate the motor continuously at its nominal
power level (80 W) for no longer than the time stipulated on
the specifications label (20 min). If you fail to observe this
time limit the motor will overheat. During the OFF period the
motor will cool again to its starting temperature.
Operating mode S6 30%: Continuous operation with idling
(cycle time 10 minutes). To ensure that the motor does not
become excessively hot, it may only be operated for 30% of
the cycle at the specified rating and must then be allowed to
idle for 70% of the cycle.
Sound and vibration
Sound and vibration values were measured in accordance
with EN 61029.
Operation Idle speed
LpA sound pressure level:
80.2 dB
65.1 dB
LWA sound power level:
88.4 dB
74.8 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing. Keep the
noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
