Taurus ABDUCTOR AND ADDUCTOR IT95, Owner'S Manual

Page: 30 / 39

STEP 7
1. Attach four 4.5" Pulleys (#32) to the Weight Stack Frame ASSY (#1) using:
four M10*50 SHCS (#67) seven Φ11*Φ20*2 Flat Washer (#57)
three M10 Nylon Lock Nut (#60)
2. Attach one 4.5" Pulley (#32) to the Movable Pulley Frame (#22) using:
one M10*50 SHCS (#67) two Φ11*Φ20*2 Flat Washer (#57)
one M10 Nylon Lock Nut (#60)
3. Attach one Thin 4.5" Pulley (#31) and one Pulley Cover (#29) and one Threaded Column
(#71) to zhe Main Frame ASSY (#11) using:
one M10*25 SHCS (#65) one Φ11*Φ20*2 Flat Washer (#57)
one Pulley Spacer1 (#45)
4. Attach one 4.5" Pulley (#32) to the Swing Frame ASSY (#20) using:
one M10*80 SHCS (#69) two Φ11*Φ20*2 Flat Washer (#57)
one M10 Nylon Lock Nut (#60)
5. Take down one M10 Nylon Lock Nut and one M10*35 SHCS from the Tension Cable ASSY
(#26), Attach the Tension Cable ASSY (#26) to the Top Plate (#4) and the Weight Stack
Frame ASSY (#1) using:
one M10 Nylon Lock Nut (Down off) one M10*35 SHCS (Down off)
6. Attach the Cable ASSY (#27) to the Movable Pulley Frame (#22) and the Wheel Frame
ASSY (#17).
7. Attach one M4*15 SHCS to the Wheel Frame ASSY (#17).
Note: Wrench tighten bolts and Nylon Lock Nuts.
Step 8
Tips: Pre-assemble the 8 bolt into the Weight Stack Frame ASSY and Bottom Bracket ASSY,
not wrench tighten Bolts, Assemble the shroud with the bolt on. Then wrench tighten Bolts.
1. Attach the Left Front Shroud (#36) and the Right Front Shroud (#37) to the Weight Stack
Frame ASSY (#1) and the Bottom Bracket ASSY (#3) using:
four M6*20 CRPHS (#55) two M6*16 CRPHS (#54)
2. Attach the Rear Shroud (#38) to the Weight Stack Frame ASSY (#1) and the Bottom
Bracket ASSY (#3) using:
four M6*20 CRPHS (#55) two M6*16 CRPHS (#54)
3. Attach the Training Placard Cover (#8) to the Weight Stack Frame ASSY (#1) and the
Top Bracket ASSY (#2) using:
two M6*20 CRPHS (#55) two M6*10 CRPHS (#53)
4. Attach the Top Rear Shroud (#9) to the Weight Stack Frame ASSY (#1) and the Top
Bracket ASSY (#2) using:
four M6*20 CRPHS (#55)
5. Attach the Top Cover (#7) to the Weight Stack Frame ASSY (#1) using:
two M6*20 CRPHS (#55) two Spout Plug Φ16.5*6.88 (#72)
6. Attach the Anti slip cover plate (#23) to the Main Frame ASSY (#11) using:
four M6*20 CRPHS (#55)
7. Attach theCup Holder (#10) to theWeight Stack Frame ASSY (#1) using:
two M6*20 CRPHS (#55)
Note: Wrench tighten bolts.
Assembly
30