background image

©Copyright Task Force Tips LLC 2008-2021

16

LIY-300 May 28, 2021 Rev19

5.3 OPERATION OF RC MODELS

See Remote Control (RC) Monitor Electrical Controls Supplemental Instructions LIY-500 for operation of the Tornado RC Monitors.

5.4 RECOMMENDED PARK POSITION

For truck mounted applications, it is recommended that the monitor be parked in a position such that the monitor’s nozzle rests against

a bracket or support surface. If a support surface is not available, run the elevation against one of the travel stops to take some of the

backlash out of the gear drive. This will minimize bouncing of the nozzle when the apparatus is traveling. Always be sure the monitor is

properly parked before moving the truck and know the overall height to avoid damage from overhead obstructions such as doors or

bridges. See LIY-500 for information on programming PARK position.

5.5 OVERRIDE KNOBS

In the event of electrical system failure on the monitor or fire truck, the Tornado RC monitor may be manually operated with factory

supplied override knobs. To make the Tornado RC more compact, the manual override knobs may be removed. Removing the override

knobs exposes a hex so an 11/16” wrench or socket may be used for manual override. 

Figure 5.5

6.0 FLOW CHARACTERISTICS

6.1 STACKED TIPS FLOW AND REACTION

Table 6.1

NOZZLE INLET PRESSURE

NOZZLE 

DIAMETER

50 PSI

80 PSI

100 PSI

150 PSI

175 PSI

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

FLOW

(GPM)

REACTION

(LBS)

1.00”

210

80

270

120

300

150

360

230

390

260

1.25”

330

120

410

190

460

230

--

--

--

--

1.50”

470

170

--

--

--

--

--

--

--

--

FLOW EXCEEDS RATING OF THE TORNADO MONITOR

NOZZLE INLET PRESSURE

NOZZLE 

DIAMETER

4 BAR

6 BAR

8 BAR

10 BAR

12 BAR

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

FLOW

(L/min)

REACTION

(KG)

25 mm

830

40

1000

60

1200

80

1300

100

1400

120

32 mm

1300

70

1700

100

1900

130

--

--

--

--

38 mm

1900

90

--

--

--

--

--

--

--

--

FLOW EXCEEDS RATING OF THE TORNADO MONITOR

11/16” (18mm) HEX

Summary of Contents for TORNADO





















Reviews: